Experimental investigation of a reticulated porous alumina heat exchanger for high temperature gas heat recovery

The present study presents an experimental study of a prototype counter-flow heat exchanger designed to recover sensible heat from inert and reactive gases flowing through a high temperature solar reactor for splitting CO2. The tube-in-tube heat exchanger is comprised of two concentric alumina tubes, each filled with reticulated porous alumina with a nominal porosity of 80% and pore density of 5 pores per inch (ppi). The RPC provides high heat transfer surface area per unit volume (917 m(-1)) with low pressure drop. Measurements include the permeability, inertial coefficient, overall heat transfer coefficient, effectiveness and pressure drop. For laminar flow and an inlet gas temperature of 1240 K, the overall heat transfer coefficients are 36-41 W m(-2) K-1. The measured performance is in good agreement with a prior CFD model of the heat exchanger. (C) 2014 Elsevier Ltd. All rights reserved.

[1]  H.Y. Zhang,et al.  Fluid flow and heat transfer in liquid cooled foam heat sinks for electronic packages , 2005, IEEE Transactions on Components and Packaging Technologies.

[2]  A. Steinfeld,et al.  Syngas production by simultaneous splitting of H2O and CO2via ceria redox reactions in a high-temperature solar reactor , 2012 .

[3]  Devarakonda Angirasa,et al.  Experimental investigation of forced convection heat transfer augmentation with metallic fibrous materials , 2002 .

[4]  R. Mahajan,et al.  Thermophysical properties of high porosity metal foams , 2002 .

[5]  M. Trabia,et al.  Design of a Compact Ceramic High-Temperature Heat Exchanger and Chemical Decomposer for Hydrogen Production , 2012 .

[6]  S. Tassou,et al.  Thermal analysis on metal-foam filled heat exchangers. Part I: Metal-foam filled pipes , 2006 .

[7]  Gilles Flamant,et al.  Thermochemical hydrogen production from a two-step solar-driven water-splitting cycle based on cerium oxides , 2006 .

[8]  Robert J. Moffat.  Gas Temperature Measurement , 1962 .

[9]  R. J. Panlener,et al.  A thermodynamic study of nonstoichiometric cerium dioxide , 1975 .

[10]  J. Jeong,et al.  High temperature heat exchanger studies for applications to gas turbines , 2009 .

[11]  Luke J. Venstrom,et al.  Enhanced Oxidation Kinetics in Thermochemical Cycling of CeO2 through Templated Porosity , 2013 .

[12]  J. Richardson,et al.  Properties of ceramic foam catalyst supports: pressure drop , 2000 .

[13]  Luke J. Venstrom,et al.  The Effects of Morphology on the Oxidation of Ceria by Water and Carbon Dioxide , 2012 .

[14]  Jane H. Davidson,et al.  Efficient splitting of CO2 in an isothermal redox cycle based on ceria , 2014 .

[15]  Wojciech Lipiński,et al.  EFFICIENCY OF TWO-STEP SOLAR THERMOCHEMICAL NON-STOICHIOMETRIC REDOX CYCLES WITH HEAT RECOVERY , 2012 .

[16]  Jack Legrand,et al.  Pressure drop prediction for flow through high porosity metallic foams , 1994 .

[17]  A. McDaniel.  Solar Hydrogen Production with a Metal Oxide-Based Thermochemical Cycle , 2012 .

[18]  Q. Zeng,et al.  Theoretical Investigation for the Active-to-Passive Transition in the Oxidation of Silicon Carbide , 2008 .

[19]  H. Anderson,et al.  Fabrication and Joining of Ceramic Compact Heat Exchangers for Process Integration , 2012 .

[20]  Eugenio Urquiza,et al.  Transient Thermal, Hydraulic, and Mechanical Analysis of a Counter Flow Offset Strip Fin Intermediate Heat Exchanger using an Effective Porous Media Approach , 2009 .

[21]  S. Haile,et al.  High-temperature isothermal chemical cycling for solar-driven fuel production. , 2013, Physical chemistry chemical physics : PCCP.

[22]  Dimos Poulikakos,et al.  Metal foams as compact high performance heat exchangers , 2003 .

[23]  R. Knitter,et al.  Testing and simulation of ceramic micro heat exchangers , 2008 .

[24]  Luke J. Venstrom,et al.  Thermodynamic Analysis of Isothermal Redox Cycling of Ceria for Solar Fuel Production , 2013 .

[25]  Savvas A. Tassou,et al.  Thermal analysis on metal-foam filled heat exchangers. Part II: Tube heat exchangers , 2006 .

[26]  J. L. Lage,et al.  Protocol for measuring permeability and form coefficient of porous media , 2005 .

[27]  A. Steinfeld,et al.  Tomography based determination of permeability, Dupuit–Forchheimer coefficient, and interfacial heat transfer coefficient in reticulate porous ceramics , 2008 .

[28]  T. Lu,et al.  Heat transfer in open-cell metal foams , 1998 .

[29]  W. Chueh,et al.  A thermochemical study of ceria: exploiting an old material for new modes of energy conversion and CO2 mitigation , 2010, Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences.

[30]  P. Peterson,et al.  Design, Fabrication, and Testing of Ceramic Plate‐Type Heat Exchangers with Integrated Flow Channel Design , 2011 .

[31]  Thomas Fend,et al.  Experimental investigation of compact silicon carbide heat exchangers for high temperatures , 2011 .

[32]  Donato Aquaro,et al.  High Temperature Compact Heat Exchangers: Performance of Advanced Metallic Recuperators for Power Plants , 2005 .

[33]  W. Chueh,et al.  High-Flux Solar-Driven Thermochemical Dissociation of CO2 and H2O Using Nonstoichiometric Ceria , 2010, Science.