In situ drilling and milling of thin sheet using microelectrical discharge machining

[1]  S. Kar,et al.  Experimental Investigation of Machinability and Surface Characteristics in Microelectrical Discharge Milling of Titanium, Stainless Steel and Copper , 2019, Arabian Journal for Science and Engineering.

[2]  S. Kar,et al.  Effect of non-electrical parameters in fabrication of micro rod using BEDG , 2019, Materials and Manufacturing Processes.

[3]  J. Bai,et al.  Fabrication of microelectrode with large aspect ratio and precision machining of micro-hole array by micro-EDM , 2019, Journal of Materials Processing Technology.

[4]  Ashutosh Kumar Singh,et al.  Analysis of micro-rods machined using reverse micro-EDM , 2018, Journal of the Brazilian Society of Mechanical Sciences and Engineering.

[5]  J. Bai,et al.  Micro-EDM method to fabricate three-dimensional surface textures used as SERS-active substrate , 2018, Applied Surface Science.

[6]  D. Reynaerts,et al.  Simulation and experimental analysis of alternating-current phenomenon in micro-EDM with a RC-type generator , 2018 .

[7]  S. Kar,et al.  Electrode wear phenomenon and its compensation in micro electrical discharge milling: A review , 2018 .

[8]  Yao Sun,et al.  Experimental study on the microelectrodes fabrication using low speed wire electrical discharge turning (LS-WEDT) combined with multiple cutting strategy , 2017 .

[9]  Paul Morantz,et al.  Current trends and future of sequential micro-machining processes on a single machine tool , 2017 .

[10]  Ahmed A. D. Sarhan,et al.  Micro-electrode fabrication processes for micro-EDM drilling and milling: a state-of-the-art review , 2017 .

[11]  Xiaodong Yang,et al.  Study on machining characteristics of micro EDM with high spindle speed using non-contact electric feeding method , 2017 .

[12]  M. Noordin,et al.  Development of new fabrication and measurement techniques of micro-electrodes with high aspect ratio for micro EDM using typical EDM machine , 2017 .

[13]  P. Singh,et al.  Influence of process parameters on the surface integrity of micro-holes of SS304 obtained by micro-EDM , 2016, Journal of the Brazilian Society of Mechanical Sciences and Engineering.

[14]  Shiv Gopal Kapoor,et al.  Modeling of Melt-Pool Formation and Material Removal in Micro-Electrodischarge Machining , 2015 .

[15]  G. Maccarini,et al.  Process performance of micro-EDM drilling of stainless steel , 2014 .

[16]  G. Karthikeyan,et al.  BLOCK EDG: ISSUES AND APPLICABILITY IN MULTIPLE PASS µED-MILLING , 2014 .

[17]  D. Sheu,et al.  Micro Three-Dimensional Cavities Tools Fabrication on PCD by µ-EDM Scanning Process , 2012 .

[18]  Janakarajan Ramkumar,et al.  A microscopic investigation of machining behavior in μED-milling process , 2012 .

[19]  Muhammad P. Jahan,et al.  On-machine fabrication of high-aspect-ratio micro-electrodes and application in vibration-assisted micro-electrodischarge drilling of tungsten carbide , 2010 .

[20]  Y. Wong,et al.  A study on the quality micro-hole machining of tungsten carbide by micro-EDM process using transistor and RC-type pulse generator , 2009 .

[21]  A. Hosokawa,et al.  Micro-electrical discharge machining of micro-rods using tool electrodes with high electrical resistivity , 2019, Precision Engineering.

[22]  S. Agarwal,et al.  Experimental investigation into the micro-EDM characteristics of conductive SiC , 2016 .

[23]  Samad Nadimi Bavil Oliaei,et al.  On-machine fabrication of PCD and WC micro end mills using micro electro discharge machining , 2014 .

[24]  Hans Kurt Tönshoff,et al.  Three-Dimensional Micromachining by Machine Tools , 1997 .