Computational Predictions of Heat Transfer and Film-Cooling for a Turbine Blade With Non-Axisymmetric Endwall Contouring

Three-dimensional contouring of the compressor and turbine endwalls in a gas turbine engine has been shown to be an effective method of reducing aerodynamic losses by mitigating the strength of the complex vortical structures generated at the endwall. Reductions in endwall heat transfer in the turbine have been also previously measured and reported in the literature. In this study, computational fluid dynamics simulations of a turbine blade with and without non-axisymmetric endwall contouring were compared to experimental measurements of the exit flowfield, endwall heat transfer and endwall film-cooling. Secondary kinetic energy at the cascade exit was closely predicted with a simulation using the SST k-ω turbulence model. Endwall heat transfer was overpredicted in the passage for both the SST k-ω and realizable k-e turbulence models, but heat transfer augmentation for a non-axisymmetric contour relative to a flat endwall showed fair agreement to the experiment. Measured and predicted film-cooling results indicated that the non-axisymmetric contouring limits the spread of film-cooling flow over the endwall depending upon the interaction of the film with the contour geometry.Copyright © 2010 by ASME

[1]  Arun K. Saha,et al.  Computations of Turbulent Flow and Heat Transfer Through a Three-Dimensional Nonaxisymmetric Blade Passage , 2008 .

[2]  Sumanta Acharya,et al.  Measured Endwall Flow and Passage Heat Transfer in a Linear Blade Passage With Endwall and Leading Edge Modifications , 2007 .

[3]  Tom Shih,et al.  CFD Analysis of Film Cooling , 2006 .

[4]  F. Menter.  Two-equation eddy-viscosity turbulence models for engineering applications , 1994 .

[5]  Chiyuki Nakamata,et al.  Computational Predictions of Endwall Film Cooling for a Turbine Nozzle Vane With an Asymmetric Contoured Passage , 2008 .

[6]  Karen A. Thole,et al.  Heat Transfer for a Turbine Blade With Non-Axisymmetric Endwall Contouring , 2009 .

[7]  I. Popovic,et al.  Comparative Investigation of Three Highly Loaded LP Turbine Airfoils: Part I — Measured Profile and Secondary Losses at Design Incidence , 2007 .

[8]  Glen C Snedden,et al.  The Application of Non-Axisymmetric Endwall Contouring in a Single Stage, Rotating Turbine , 2009 .

[9]  Martin G. Rose,et al.  Improving Efficiency of a High Work Turbine Using Non-Axisymmetric Endwalls: Part I—Endwall Design and Performance , 2008 .

[10]  Stefan Kern,et al.  Predictions of External Heat Transfer for Turbine Vanes and Blades With Secondary Flowfields , 2003 .

[11]  Robert J. Moffat,et al.  Describing the Uncertainties in Experimental Results , 1988 .

[12]  David Gregory-Smith,et al.  Non-Axisymmetric Turbine End Wall Design: Part II — Experimental Validation , 1999 .

[13]  Andrew Duggleby,et al.  Identifying Inefficiencies in Unsteady Pin Fin Heat Transfer , 2009 .

[14]  Marc G. Nagel,et al.  Experimentally Verified Numerical Optimization of a Three-Dimensional Parametrized Turbine Vane With Nonaxisymmetric End Walls , 2005 .

[15]  Reza S. Abhari,et al.  Improving Efficiency of a High Work Turbine Using Non-Axisymmetric Endwalls: Part II—Time-Resolved Flow Physics , 2008 .

[16]  Srinath V. Ekkad,et al.  Flow and Heat Transfer Predictions for a Flat-Tip Turbine Blade , 2002 .

[17]  Steen A. Sjolander,et al.  Measurements of Secondary Losses in a Turbine Cascade With the Implementation of Non-Axisymmetric Endwall Contouring , 2008 .

[18]  Sumanta Acharya,et al.  Flow Dynamics and Film Cooling Effectiveness on a Non-Axisymmetric Contour Endwall in a Two-Dimensional Cascade Passage , 2009 .

[19]  Steen A. Sjolander,et al.  Active Flow Control Using Steady Blowing for a Low-Pressure Turbine Cascade , 2004 .

[20]  Steen A. Sjolander,et al.  Application of Non-Axisymmetric Endwall Contouring to Conventional and High-Lift Turbine Airfoils , 2007 .

[21]  David Gregory-Smith,et al.  Non-Axisymmetric Turbine End Wall Design: Part I — Three-Dimensional Linear Design System , 1999 .

[22]  Sumanta Acharya,et al.  Flowfield in a Film-Cooled Three-Dimensional Contoured Endwall Passage: Aerodynamic Measurements , 2007 .

[23]  J. Whitelaw,et al.  Convective heat and mass transfer , 1966 .

[24]  T. Shih,et al.  A New K-epsilon Eddy Viscosity Model for High Reynolds Number Turbulent Flows: Model Development and Validation , 1994 .

[25]  J. Bons,et al.  Turbine Separation Control Using Pulsed Vortex Generator Jets , 2000 .

[26]  D. G. Gregory-Smith,et al.  Turbulence Modeling for Secondary Flow Prediction in a Turbine Cascade , 1992 .

[27]  Karen A. Thole,et al.  Gas Turbine Film Cooling , 2006 .

[28]  I. Popovic,et al.  Aerodynamics of a Family of Three Highly Loaded Low-Pressure Turbine Airfoils: Measured Effects of Reynolds Number and Turbulence Intensity in Steady Flow , 2006 .

[29]  David G. Bogard,et al.  Comparison of RANS Turbulence Models for Prediction of Film Cooling Performance , 2008 .

[30]  D. K. Walters,et al.  A Detailed Analysis of Film–Cooling Physics: Part I — Streamwise Injection With Cylindrical Holes , 1997 .

[31]  Steen A. Sjolander,et al.  Measurements of Secondary Losses in a High-Lift Front-Loaded Turbine Cascade With the Implementation of Non-Axisymmetric Endwall Contouring , 2009 .