Topology optimization of free-layer damping material on a thin panel for maximizing modal loss factors expressed by only real eigenvalues

Abstract Damping material is usually applied to steel panels of vehicles to reduce vibration levels. On the other hand, the weight of a vehicle must be reduced to improve the rate of fuel consumption. Therefore, the modal loss factors caused by the treatment of damping material on the steel panels of a vehicle body structure must be maximized within a given volume. In this paper, we propose a practical design method to maximize modal loss factors by optimizing the layout of damping material under a volume constraint. The modal loss factor for an eigenmode can be obtained conventionally by the modal strain energy method as the material loss factor multiplied by the ratio of the strain energy stored in the damping material over the total strain energy in the system under consideration. In the proposed method, we assume that the eigenvectors with damping material are almost identical with the eigenvectors without damping material. The modal loss factor can then be expressed approximately by using a corresponding real eigenvalue, for which the stiffness of the damping material is taken into account but its mass density is set to zero and ignored. Several numerical examples are provided to demonstrate that the proposed method obtains optimal layouts of damping material applied to a flat rectangular panel. Our results indicate that the damping material is mainly distributed in areas where strain energy is stored, which agrees well with the results obtained using conventional design methodologies. Moreover, by applying a design sensitivity filter that was improved recently, the layout of damping material can be unified into a single domain to meet practical requirements for manufacturing.

[1]  Frithiof I. Niordson,et al.  Optimal design of elastic plates with a constraint on the slope of the thickness function , 1983 .

[2]  A. Lumsdaine,et al.  SHAPE OPTIMIZATION OF UNCONSTRAINED VISCOELASTIC LAYERS USING CONTINUUM FINITE ELEMENTS , 1998 .

[3]  J. Petersson,et al.  Numerical instabilities in topology optimization: A survey on procedures dealing with checkerboards, mesh-dependencies and local minima , 1998 .

[4]  M. Bendsøe,et al.  Topology Optimization: "Theory, Methods, And Applications" , 2011 .

[5]  E. Kerwin.  Damping of Flexural Waves by a Constrained Viscoelastic Layer , 1959 .

[6]  Sun Yong Kim,et al.  Optimal damping layout in a shell structure using topology optimization , 2013 .

[7]  Lars Damkilde,et al.  Topology Optimization - Improved Checker-Board Filtering With Sharp Contours , 2006 .

[8]  Hui Zheng,et al.  Optimization of partial constrained layer damping treatment for vibrational energy minimization of vibrating beams , 2004 .

[9]  C. S. Jog,et al.  A new approach to variable-topology shape design using a constraint on perimeter , 1996 .

[10]  Mohan D. Rao,et al.  Recent applications of viscoelastic damping for noise control in automobiles and commercial airplanes , 2003 .

[11]  K. Svanberg.  The method of moving asymptotes—a new method for structural optimization , 1987 .

[12]  M. Bendsøe,et al.  Material interpolation schemes in topology optimization , 1999 .

[13]  K. Matsui,et al.  Continuous approximation of material distribution for topology optimization , 2004 .

[14]  Adel Elsabbagh,et al.  Topology Optimization of Constrained Layer Damping on Plates Using Method of Moving Asymptote (MMA) Approach , 2011 .

[15]  Marco Danti,et al.  Modal Methodology for the Simulation and Optimization of the Free-Layer Damping Treatment of a Car Body , 2010 .

[16]  Kenan Y. Sanliturk,et al.  Optimisation of damping treatments based on big bang–big crunch and modal strain energy methods , 2014 .

[17]  Ping Zhu,et al.  Acoustic analysis of damping structure with response surface method , 2007 .

[18]  T. Lassila.  Optimal damping of a membrane and topological shape optimization , 2009 .

[20]  S. Rahmatalla,et al.  A Q4/Q4 continuum structural topology optimization implementation , 2004 .

[21]  Jun Yang,et al.  Experimental study of the effect of viscoelastic damping materials on noise and vibration reduction within railway vehicles , 2009 .

[22]  James K. Guest,et al.  Achieving minimum length scale in topology optimization using nodal design variables and projection functions , 2004 .

[23]  Kohei Yuge,et al.  Optimal Layout of Damping Material Using Homogenization Method. , 1999 .

[24]  G. Cheng,et al.  On topology optimization of damping layer in shell structures under harmonic excitations , 2012 .

[25]  良夫 黒沢,et al.  制振材を積層した自動車車体用パネルの減衰特性の有限要素解析 : 第1報,ビードパネルの減衰特性の実験結果と数値計算結果の比較(機械力学,計測,自動制御) , 2003 .

[26]  Conor D. Johnson,et al.  Finite Element Prediction of Damping in Structures with Constrained Viscoelastic Layers , 1981 .

[27]  O. Sigmund.  Morphology-based black and white filters for topology optimization , 2007 .

[28]  Zhan Kang,et al.  Topology optimization of damping layers for minimizing sound radiation of shell structures , 2013 .