Facile non thermal plasma based desorption of self assembled monolayers for achieving low temperature and low pressure Cu–Cu thermo-compression bonding

This paper reports Self Assembled Monolayer (SAM) of propanethiol desorption assisted low temperature, low pressure copper to copper (Cu–Cu) thermo-compression bonding, a technique which could potentially open up a whole new platform for developing next generation heterogeneous smart devices using 3D integrated circuit technology. Thiolated self assembled monolayers protect a freshly deposited copper surface from oxidation and other contamination. Removal of this SAM layer just prior to bonding would potentially bring down temperature and pressure thus rendering the process CMOS compatible. This paper focuses on using Non-Thermal Plasma (NTP) desorption, which is a simple, robust, room temperature technique for desorbing SAMs. The desorption was carried out in an indigenous chamber specifically designed for this purpose. Thermo-compression bonding post desorption resulted in a very good quality bonding with a bond strength of 132 MPa, performed at a relatively low temperature of 200 °C and a low pressure of 5 bar.

[1]  C.C. Wong,et al.  Low Temperature Copper-Copper Thermocompression Bonding , 2008, 2008 10th Electronics Packaging Technology Conference.

[2]  S. Nai,et al.  Advanced high density interconnect materials and techniques , 2009, 2009 International Conference on Electronic Packaging Technology & High Density Packaging.

[3]  Chuan Seng Tan,et al.  (Invited) Cu Surface Passivation with Self-Assembled Monolayer (SAM) and Its Application for Wafer Bonding at Moderately Low Temperature , 2013 .

[4]  A. Dutta,et al.  Room temperature desorption of Self Assembled Monolayer from Copper surface for low temperature & low pressure thermocompression bonding , 2015, 2015 IEEE 65th Electronic Components and Technology Conference (ECTC).

[5]  Tai-Hong Chen,et al.  Effects of Bonding Parameters on the Reliability of Fine-Pitch Cu/Ni/SnAg Micro-Bump Chip-to-Chip Interconnection for Three-Dimensional Chip Stacking , 2012, IEEE Transactions on Device and Materials Reliability.

[6]  H. Y. Li,et al.  High density bump-less Cu-Cu bonding with enhanced quality achieved by pre-bonding temporary passivation for 3D wafer stacking , 2011, Proceedings of 2011 International Symposium on VLSI Technology, Systems and Applications.

[7]  Chuan Seng Tan,et al.  Silicon Multilayer Stacking Based on Copper Wafer Bonding , 2005 .

[8]  Karen Maex,et al.  A thermal stability study of alkane and aromatic thiolate self-assembled monolayers on copper surfaces , 2004 .

[9]  D. F. Lim,et al.  Temporary passivation of Cu for low temperature (< 300°C) 3D wafer stacking , 2011, 2011 IEEE International Interconnect Technology Conference.

[10]  Chuan Seng Tan,et al.  High-Density 3-D Interconnect of Cu–Cu Contacts With Enhanced Contact Resistance by Self-Assembled Monolayer (SAM) Passivation , 2011, IEEE Transactions on Electron Devices.

[11]  Yunsoo Kim,et al.  Self-Assembled Monolayers of Alkanethiols on Oxidized Copper Surfaces , 2000 .

[12]  D. F. Lim,et al.  Enhancing Cu-Cu Diffusion Bonding at Low Temperature Via Application of Self-assembled Monolayer Passivation , 2011 .

[13]  Ching-Te Chuang,et al.  Novel Cu-to-Cu Bonding With Ti Passivation at 180 $^{\circ}{\rm C}$ in 3-D Integration , 2013, IEEE Electron Device Letters.

[14]  Duixian Liu,et al.  A Ball Grid Array Package With a Microstrip Grid Array Antenna for a Single-Chip 60-GHz Receiver , 2011, IEEE Transactions on Antennas and Propagation.

[15]  R. Gutmann,et al.  Wafer Level 3-D ICs Process Technology , 2008 .

[16]  P. Ghosal,et al.  The Reinforcement Ability of Plasma-Etched Carbon Nanofibers on Mechanical Properties of C-Epoxy Composites , 2014 .

[17]  T. Itoh,et al.  Bumpless interconnect through ultrafine Cu electrodes by means of surface-activated bonding (SAB) method , 2006, IEEE Transactions on Advanced Packaging.

[18]  H. Yamada,et al.  Surface properties of activated carbon treated by cold plasma heating , 2007 .