Finite Element mesh coarsening for effective distortion prediction in Wire Arc Additive Manufacturing

Abstract WAAM (Wire Arc Additive Manufacturing) is a metal AM (Additive Manufacturing) technology that allows high deposition rates and the manufacturability of very large components, compared to other AM technologies. Distortions and residual stresses affecting the manufactured parts represent the main drawbacks of this AM technique. FE (Finite Element) modeling could represent an effective tool to tackle such issues, since it can be used to optimize process parameters, deposition paths and to test alternative mitigation strategies. Nevertheless, specific modeling strategies are needed to reduce the computational cost of the process simulation, such as reducing the number of elements used in discretizing the model. This paper presents an alternative technique to reduce the number of elements required to discretize the substrates of WAAM workpieces. The proposed technique is based on dividing the substrate in several zones, separately discretized and then connected by means of a double sided contact algorithm. This strategy allows to achieve a significant reduction of the number of elements required, without affecting their quality parameters. The geometry and dimension of the mesh zones are identified through a dedicated algorithm that allows to achieve an accurate temperature prediction with the minimum element number. The effectiveness of the proposed technique was tested by means of both numerical and experimental validation tests.

[1]  J. Falkus,et al.  Application of Thermal Analysis Tests Results in the Numerical Simulations of Continuous Casting Process , 2015 .

[2]  John Lancaster,et al.  The Physics of Welding , 1984 .

[3]  Gianni Campatelli,et al.  A heuristic approach to meet geometric tolerance in High Pressure Die Casting , 2012, Simul. Model. Pract. Theory.

[4]  O. C. Zienkiewicz,et al.  The Finite Element Method for Solid and Structural Mechanics , 2013 .

[5]  K. Salonitis,et al.  Simulation of metallic powder bed additive manufacturing processes with the finite element method: A critical review , 2017 .

[6]  Paul A. Colegrove,et al.  A computationally efficient finite element model of wire and arc additive manufacture , 2013, The International Journal of Advanced Manufacturing Technology.

[7]  Pan Michaleris,et al.  Mitigation of distortion in large additive manufacturing parts , 2017 .

[8]  Gianni Campatelli,et al.  3D Finite Element Modeling of Holder-Tool Assembly for Stability Prediction in Milling☆ , 2015 .

[9]  Miguel Cervera,et al.  Finite element modeling of multi-pass welding and shaped metal deposition processes , 2010 .

[10]  Richard M. Everson,et al.  Finite element simulation of the temperature and stress fields in single layers built without-support in selective laser melting , 2013 .

[11]  John N. DuPont,et al.  Thermal efficiency of arc welding processes , 1995 .

[12]  Lin Wu,et al.  Three-dimensional finite element analysis of thermal stress in single-pass multi-layer weld-based rapid prototyping , 2012 .

[13]  Konstantinos Salonitis,et al.  Additive manufacturing and post-processing simulation: laser cladding followed by high speed machining , 2016 .

[14]  Paul A. Colegrove,et al.  Investigation of the benefits of plasma deposition for the additive layer manufacture of Ti–6Al–4V , 2012 .

[15]  Paul A. Colegrove,et al.  Thermo-mechanical analysis of Wire and Arc Additive Layer Manufacturing process on large multi-layer parts , 2011 .

[16]  P. Michaleris,et al.  Prediction of welding distortion , 1997 .

[17]  Pan Michaleris,et al.  Finite element modeling discretization requirements for the laser forming process , 2004 .

[18]  Gianni Campatelli,et al.  Finite Element Modelling of Wire-arc-additive-manufacturing Process , 2016 .

[19]  J. Goldak,et al.  A new finite element model for welding heat sources , 1984 .

[20]  J. Goldak,et al.  Computer modeling of heat flow in welds , 1986 .

[21]  P. Michaleris,et al.  Residual stress and distortion modeling of electron beam direct manufacturing Ti-6Al-4V , 2015 .

[22]  O. C. Zienkiewicz,et al.  The Finite Element Method: Its Basis and Fundamentals , 2005 .

[23]  P. Michaleris.  Modeling metal deposition in heat transfer analyses of additive manufacturing processes , 2014 .

[24]  Minking K. Chyu,et al.  Finite element modeling and validation of thermomechanical behavior of Ti-6Al-4V in directed energy deposition additive manufacturing , 2016 .

[25]  Yuh J. Chao,et al.  Effects of temperature-dependent material properties on welding simulation , 2002 .

[26]  Understanding welding distortion: thermal fields thermo-mechanical effects , 2014 .

[27]  O. Zienkiewicz,et al.  Material Constitution Using Representative Volume Elements , 2014 .

[28]  Pan Michaleris,et al.  Thermomechanical Modeling of Additive Manufacturing Large Parts , 2014 .

[29]  Hidekazu Murakawa,et al.  Prediction of welding distortion in a curved plate structure by means of elastic finite element method , 2008 .

[30]  F. Kreith,et al.  Principles of heat transfer , 1962 .

[31]  Paul A. Colegrove,et al.  Microstructure and residual stress improvement in wire and arc additively manufactured parts through high-pressure rolling , 2013 .

[32]  P. Michaleris,et al.  Thermo‐elasto‐plastic finite element analysis of quasi‐state processes in Eulerian reference frames , 2002 .

[33]  Gianni Campatelli,et al.  Cutting Forces Analysis in Additive Manufactured AISI H13 Alloy , 2016 .

[34]  Pan Michaleris,et al.  Effect of stress relaxation on distortion in additive manufacturing process modeling , 2016 .