The influence of hydrogen loading and the fabrication process on the mechanical strength of optical fibre Bragg gratings

Abstract This paper investigates the influence of hydrogen loading and other stages of the fabrication process on the mechanical strength of fibre Bragg gratings. Following UV irradiation, tensile tests were carried out on Ge–B codoped photosensitive fibres with and without hydrogen loading. Fibre Bragg gratings (FBGs) were written using a range of UV wavelengths, namely 246, 255 and 266 nm. The tensile strength of the optical fibres was determined in their as-received status and following the various stages of FBG fabrication. The mechanical strength was assessed using Weibull statistics. The results indicate that the strength of FBGs is influenced by the UV irradiation parameters and by the hydrogen-loading process. FBGs fabricated using shorter UV wavelengths and low pulse power intensity exhibit a high mechanical strength. The FBGs written in hydrogen loaded fibres have less than 50% of the strength of FBGs that have not been hydrogen loaded. Fibre fracture morphology observed by scanning electron microscope reveals fracture mechanisms of FBGs, which are correlated with the structural change of the silica fibres induced during the FBG inscription process. Combined with surface information gathered by atomic force microscopy, fracture mechanics is applied to understand the mechanisms of strength degradation caused by the FBG inscription process.

[1]  Ralph P. Tatam,et al.  AFM observation of surface topography of fibre Bragg gratings fabricated in germanium-boron codoped fibres and hydrogen-loaded fibres , 2002 .

[2]  Martin A. Putnam,et al.  Fibre strength unaffected by on-line writing of single-pulse Bragg gratings , 1997 .

[3]  Willem Griffioen,et al.  Reliability of Optical Fibres and Components , 1999 .

[4]  Ralph P. Tatam,et al.  Fibre Bragg gratings fabricated using a wavelength tuneable laser source and a phase mask based interferometer , 1996 .

[5]  W. C. Levengood.  Effect of Origin Flaw Characteristics on Glass Strength , 1958 .

[6]  R P Salathé,et al.  Fabrication of high-mechanical-resistance Bragg gratings in single-mode optical fibers with continuous-wave ultraviolet laser side exposure. , 1998, Optics letters.

[7]  David N. Payne,et al.  Single pulse Bragg gratings written during fibre drawing , 1993 .

[8]  Jacques Albert,et al.  Effective index drift from molecular hydrogen diffusion in hydrogen-loaded optical fibres and its effect on Bragg grating fabrication , 1994 .

[9]  P. Lemaire,et al.  High pressure H/sub 2/ loading as a technique for achieving ultrahigh UV photosensitivity and thermal sensitivity in GeO/sub 2/ doped optical fibres , 1993 .

[10]  Ralph P. Tatam,et al.  Influence of process route on mechanical and sensing performance of fiber Bragg grating optical sensors , 1999, Smart Structures.

[11]  Charles R. Kurkjian,et al.  Acid stripping of fused silica optical fibers without strength degradation , 1997 .

[12]  A. A. Griffith.  The Phenomena of Rupture and Flow in Solids , 1921 .

[13]  Hans G. Limberger,et al.  UV-induced mechanical degradation of optical fibres , 1997 .

[14]  Vincent A. Handerek,et al.  Mechanical strength degradation of UV exposed optical fibres , 1997 .

[15]  Victor Mizrahi,et al.  Mechanisms of enhanced UV photosensitivity via hydrogen loading in germanosilicate glasses , 1993 .

[16]  D. Rooke,et al.  The compendium of stress intensity factors , 1978, International Journal of Fracture.

[17]  S. Simmens,et al.  The measurement of glass fibre strength in composites from studies of their fracture surfaces , 1983 .