Effects of Inlet Flow Field Conditions on the Performance of Centrifugal Compressor Diffusers: Part 2—Straight-Channel Diffuser

This is Part 2 of an examination of the influence of inlet flow conditions on the performance and operating range of centrifugal compressor vaned diffusers. The paper describes tests of a straight-channel type diffuser, sometimes called a wedge-vane diffuser, and compares the results with those from the discrete-passage diffusers described in Part 1. Effects of diffuser inlet Mach number, flow angle, blockage, and axial flow nonuniformity on diffuser pressure recovery and operating range are addressed. The straight-channel diffuser investigated has 30 vanes and was designed for the same aerodynamic duty as the discrete-passage diffuser described in Part 1. The ranges of the overall pressure recovery coefficients were 0.50-0.78 for the straight-channel diffuser and 0.50-0.70 for the discrete-passage diffuser, except when the diffuser was choked. In other words, the maximum pressure recovery of the straight-channel diffuser was found to be roughly 10 percent higher than that of the discrete-passage diffuser investigated. The two types of diffuser showed similar behavior regarding the dependence of pressure recovery on diffuser inlet flow angle and the insensitivity of the performance to inlet flow field axial distortion and Mach number. The operating range of the straight-channel diffuser, as for the discrete-passage diffusers, was limited by the onset of rotating stall at a fixed momentum-averaged flow angle into the diffuser, which was for the straight-channel diffuser, α crit = 70 ± 0.5 deg. The background, nomenclature, and description of the facility and method are all given in Part 1.

[1]  David Japikse,et al.  Optimization of Industrial Centrifugal Compressors: Part 6A — Studies in Component Performance — Eight Design Cases From 1972 to 1982 , 1986 .

[2]  S. J. Kline,et al.  Performance and Design of Straight, Two-Dimensional Diffusers , 1967 .

[3]  David Japikse,et al.  Optimization of Industrial Centrifugal Compressors: Part 6B — Studies in Component Performance — Laboratory Development of Eight Stages From 1972 to 1982 , 1986 .

[4]  T. Sakai,et al.  Development of a High Pressure Ratio Centrifugal Compressor for 300kW-Class Ceramic Gas Turbine , 1997 .

[5]  C. Rodgers.  The Performance of Centrifugal Compressor Channel Diffusers , 1982 .

[6]  Nicholas A. Cumpsty,et al.  Effects of Inlet Flow Field Conditions on the Performance of Centrifugal Compressor Diffusers: Part 1—Discrete-Passage Diffuser , 2000 .

[7]  M. Yaras,et al.  Effects of inlet conditions on the flow in a fishtail curved diffuser with strong curvature , 1996 .

[8]  Hideo Nishida,et al.  Aerodynamic Performance of a Centrifugal Compressor With Vaned Diffusers , 1980 .

[9]  H. Krain.  Experimental Observation of the Flow in Impellers and Diffusers , 1984 .

[10]  Robert C. Dean,et al.  Straight Channel Diffuser Performance at High Inlet Mach Numbers , 1969 .

[11]  Colin Rodgers,et al.  Design Considerations for High-Pressure-Ratio Centrifugal Compressors , 1972 .

[12]  Victor Gregory Filipenco.  Experimental investigation of flow distortion effects on the performance of radial discrete-passage diffusers , 1991 .

[13]  D. P. Kenny.  A Comparison of the Predicted and Measured Performance of High Pressure Ratio Centrifugal Compressor Diffusers , 1972 .

[14]  Fumikata Kano,et al.  Aerodynamic Performance of Large Centrifugal Compressors , 1982 .