Macroscopic and microscopic aspects of the deformation and fracture mechanisms of ultrafine-grained aluminum processed by hot isostatic pressing

Abstract A commercial purity aluminum nano-powder has been consolidated by the hot isostatic pressing technique. The bulk material, in addition to the unavoidable native Al2O3 phase, has a microstructure comprising a fraction of microcrystalline grains (⩾500 nm) that are embedded in an ultrafine-grained matrix (150 nm). True stress–true strain curves acquired from compressive tests at room temperature showed a rapid and brief hardening at the early stage of the deformation followed by a short stress plateau and linear work softening. The material yielded at 390 MPa – 10 times the flow stress of the coarse-grained counterpart material. The per cent reduction to rupture was about 20% mostly due to the presence of microcrystalline grains acting against crack propagation. In addition, it is shown that microcrystalline grains deform via dislocation-based mechanisms, while present evidence suggests that the matrix deforms by a cooperative grain boundary sliding.

[1]  E. Ma,et al.  Instabilities and ductility of nanocrystalline and ultrafine-grained metals , 2003 .

[2]  D. Dunand,et al.  High-strain-rate deformation of pure aluminum reinforced with 25% alumina submicron particles near the solidus temperature , 1999 .

[3]  K. T. Ramesh,et al.  Nano-structured vanadium: processing and mechanical properties under quasi-static and dynamic compression , 2004 .

[4]  P. Sanders,et al.  The strength of nanocrystalline metals with and without flaws , 1997 .

[5]  A. Mukherjee,et al.  Geometrical aspects of superplastic flow , 1996 .

[6]  X. G. Zhu,et al.  The temperature influence on the microscopic characteristics of plastic deformation morphologies in nanocrystalline Ni–Fe investigated with atomic force microscopy , 2004 .

[7]  I. Ovid’ko,et al.  Triple junction nanocracks in deformed nanocrystalline materials , 2004 .

[8]  C. Rizkallah,et al.  Advanced process control of hot isostatic pressing. Application to Astroloy HIP , 2001 .

[9]  Paul G. Sanders,et al.  Elastic and tensile behavior of nanocrystalline copper and palladium , 1997 .

[10]  E. Lavernia,et al.  Mechanical behavior and microstructure of a thermally stable bulk nanostructured Al alloy , 2001 .

[11]  Patrick B. Berbon,et al.  Plastic flow and fracture behavior of an Al-Ti-Cu nanocomposite , 2001 .

[12]  J. Bigot,et al.  Synthesis and structural analysis of aluminum nanocrystalline powders , 1998 .

[13]  J. G. Sevillano,et al.  Ductilization of nanocrystalline materials for structural applications , 2004 .

[14]  K. T. Ramesh,et al.  Effect of nanocrystalline and ultrafine grain sizes on the strain rate sensitivity and activation volume: fcc versus bcc metals , 2004 .

[15]  Yinmin M Wang,et al.  Enhanced tensile ductility and toughness in nanostructured Cu , 2002 .

[16]  Yonghun Jung,et al.  ULTRA-FINE POWDER BY WIRE EXPLOSION METHOD , 2001 .

[17]  J. Weertman,et al.  Microsample tensile testing of nanocrystalline metals , 2000 .

[18]  R. Valiev.  Structure and mechanical properties of ultrafine-grained metals , 1997 .

[19]  K. T. Ramesh,et al.  Effects of nanocrystalline and ultrafine grain sizes on constitutive behavior and shear bands in iron , 2003 .

[20]  D. Dunand,et al.  Mechanical properties and microstructure of cast oxide-dispersion-strengthened aluminum , 1995 .

[21]  E. Lavernia,et al.  The mechanical behavior of a cryomilled Al-10Ti-2Cu alloy , 2001 .

[22]  Subra Suresh,et al.  Mechanical behavior of nanocrystalline metals and alloys , 2003 .

[23]  Graham T. Smith.  Getting the measure of PM machinability , 1998 .

[24]  Y. Champion,et al.  Near-Perfect Elastoplasticity in Pure Nanocrystalline Copper , 2003, Science.

[25]  Helen V. Atkinson,et al.  Fundamental aspects of hot isostatic pressing: An overview , 2000 .

[26]  S. Nutt,et al.  Al-Mg alloy engineered with bimodal grain size for high strength and increased ductility , 2003 .

[27]  J. Duval,et al.  Macroscopic behaviour versus dislocation substructures development under cyclic shear tests on the aluminium–3004 alloy , 1999 .

[28]  H. Cong,et al.  Preparation and mechanical properties of highly densified nanocrystalline Al , 2000 .

[29]  W. Blum,et al.  Transition from strengthening to softening by grain boundaries in ultrafine-grained Cu , 2004 .

[30]  E. Lavernia,et al.  Deformation and activation volumes of cryomilled ultrafine-grained aluminum , 2004 .

[31]  T. Mukai,et al.  Dynamic mechanical properties of a near-nano aluminum alloy processed by equal-channel-angular-extrusion , 1998 .

[32]  M. Victoria,et al.  Nanocrystalline electrodeposited Ni: microstructure and tensile properties , 2002 .