Identification and proposed control of helicopter transmission noise at the source

Helicopter cabin interiors require noise treatment which is expensive and adds weight. The gears inside the main power transmission are major sources of cabin noise. Work conducted by the NASA Lewis Research Center in measuring cabin interior noise and in relating the noise spectrum to the gear vibration of the Army OH-58 helicopter is described. Flight test data indicate that the planetary gear train is a major source of cabin noise and that other low frequency sources are present that could dominate the cabin noise. Companion vibration measurements were made in a transmission test stand, revealing that the single largest contributor to the transmission vibration was the spiral bevel gear mesh. The current understanding of the nature and causes of gear and transmission noise is discussed. It is believed that the kinematical errors of the gear mesh have a strong influence on that noise. The completed NASA/Army sponsored research that applies to transmission noise reduction is summarized. The continuing research program is also reviewed.

[1]  John J. Coy,et al.  Vibration characteristics of OH-58A helicopter main rotor transmission , 1987 .

[2]  H C Chao,et al.  A computer solution for the dynamic load, lubricant film thickness and surface temperatures in spiral bevel gears , 1987 .

[3]  John J. Coy,et al.  Summary of drive-train component technology in helicopters , 1984 .

[4]  C. E. Passerello,et al.  An Investigation of the Dynamic Response of Spur Gear Teeth with Moving Loads. , 1987 .

[5]  Faydor L. Litvin,et al.  New Generation Methods for Spur, Helical, and Spiral-Bevel Gears. , 1986 .

[6]  J. J. Coy,et al.  OH-58 Helicopter Transmission Failure Analysis , 1976 .

[7]  W. J. Atherton,et al.  Investigation on experimental techniques to detect, locate and quantify gear noise in helicopter transmissions , 1985 .

[8]  W. D. Mark.  The transfer function method for gear system dynamics applied to conventional and minimum excitation gearing designs , 1982 .

[9]  R. L. Huston,et al.  Dynamic loading on parallel shaft gears , 1986 .

[10]  Faydor L. Litvin,et al.  Spiral-Bevel Geometry and Gear Train Precision, , 1983 .

[11]  H. Cheng,et al.  Thermal elastohydrodynamic lubrication of spur gears , 1983 .

[12]  W. D. Mark.  Analysis of Vibratory Excitation of Gear Systems as a Contributor to Aircraft Interior Noise. [helicopter cabin noise , 1979 .

[13]  J. J. Coy,et al.  Generation of spiral bevel gears with zero kinematical errors and computer aided simulation of their meshing and contact , 1985 .

[14]  Faydor L. Litvin,et al.  Mathematical models for the synthesis and optimization of spiral bevel gear tooth surfaces. [for helicopter transmissions , 1982 .

[15]  R. L. Huston,et al.  Dynamic analysis of straight and involute tooth forms , 1984 .

[16]  L. S. Boyd,et al.  Multi-mesh gear dynamics program evaluation and enhancements , 1985 .

[17]  W. D. Mark.  Gear noise origins , 1985 .

[18]  Faydor L. Litvin,et al.  Generation of spiral bevel gears with zero kinematical errors and computer aided tooth contact analysis , 1986 .

[19]  Duane E Bassett,et al.  The design and analysis of single flank transmission error tester for loaded gears , 1987 .

[20]  A. M. Mitchell,et al.  Testing of UH-60A helicopter transmission in NASA Lewis 2240-kW (3000-hp) facility , 1986 .

[21]  Faydor L. Litvin,et al.  Method for Generation of Spiral Bevel Gears With Conjugate Gear Tooth Surfaces , 1987 .