The elastic and moisture transfer properties of polyethylene and polypropylene membranes for use in liquid-to-air energy exchangers

The elastic and moisture transfer properties of membrane materials are required when designing liquid-to-air energy exchangers composed of a series of pressurized membrane channels. Elastic properties are needed to ensure minimal deflections and moisture transfer properties are needed to ensure high moisture transfer rates between the liquid desiccant and air streams. In this research, two ASTM tension test standards (D 882 and D 4595) and circular and square bulge tests are used to determine the elastic moduli of two membranes; the dynamic moisture permeation cell is used to determine the water vapour resistance. The experimental data show the effects of membrane orientation, strain rate and relative humidity on the elastic properties and the effect of humidity on the water vapour resistance. Results show that the bulge test is best suited for the proposed application of a pressurized membrane channel since it includes biaxial effects and gives accurate data that are easy to measure and more closely represent a membrane channel under uniform pressure. The measured elastic moduli and water vapour resistances are applied to estimate the deflections of a pressurized membrane channel supported by a screen with square openings and the energy transfer effectiveness of an energy recovery system consisting of two liquid-to-air membrane energy exchangers.

[1]  Myoung-Sook Kwon,et al.  A comparison of standard methods for measuring water vapour permeability of fabrics , 2003 .

[2]  Majid Charmchi,et al.  An Automated Water Vapor Diffusion Test Method for Fabrics, Laminates, and Films , 1995 .

[3]  Xiangshan Chen,et al.  Plane-strain Bulge Test for Thin Films , 2005 .

[4]  Haisheng Fan,et al.  Performance of a Run-Around System for HVAC Heat and Moisture Transfer Applications Using Cross-Flow Plate Exchangers Coupled with Aqueous Lithium Bromide , 2006 .

[5]  Á. Lozano,et al.  Effect of substituents on the permeation properties of polyamide membranes , 2006 .

[6]  Donald Rivin,et al.  Transport properties of porous membranes based on electrospun nanofibers , 2001 .

[7]  B. J. Daniels,et al.  Accuracy and Reliability of Bulge Test Experiments , 1993 .

[8]  Jinlian Hu,et al.  Structural characterization and mass transfer properties of nonporous segmented polyurethane membrane: Influence of hydrophilic and carboxylic group , 2006 .

[9]  Petersen,et al.  A Test Method to Determine the Relative Humidity Dependence of the Air Permeability of Woven Textile Fabrics , 1997 .

[10]  Kang Li,et al.  Preparation and characterization of hydrophobic ceramic hollow fibre membrane , 2007 .

[11]  P. Gibson,et al.  Effect of temperature on water vapor transport through polymer membrane laminates , 2000 .

[12]  Carey J. Simonson,et al.  Air-to-air exchangers , 2003 .

[13]  P. Carreau,et al.  Analysis of microporous membranes obtained from polypropylene films by stretching , 2007 .

[14]  Subrata Mondal,et al.  Free volume and water vapor permeability of dense segmented polyurethane membrane , 2006 .

[15]  P Scovazzo,et al.  Hydrophilic membrane-based humidity control. , 1998, Journal of membrane science.

[16]  Xiaoqing Zhang,et al.  Synthesis and properties of poly(ether urethane) membranes filled with isophorone diisocyanate-grafted carbon nanotubes , 2007 .

[17]  M. Larson.  The performance of membranes in a newly proposed run-around heat and moisture exchanger , 2006 .

[18]  H. Fan,et al.  The polyurethane membranes with temperature sensitivity for water vapor permeation , 2007 .

[19]  Yi Jiang,et al.  HEAT AND MASS TRANSFER IN A MEMBRANE-BASED ENERGY RECOVERY VENTILATOR , 1999 .

[20]  Majid Charmchi,et al.  The use of volume‐averaging techniques to predict temperature transients due to water vapor sorption in hygroscopic porous polymer materials , 1997 .

[21]  Carey J. Simonson,et al.  Effectiveness of energy wheels from transient measurements. Part I: Prediction of effectiveness and uncertainty , 2006 .

[22]  Drew W. Johnson,et al.  Analysis of heat and mass transfer phenomena in hollow fiber membranes used for evaporative cooling , 2003 .

[23]  William D. Nix,et al.  Analysis of the accuracy of the bulge test in determining the mechanical properties of thin films , 1992 .

[24]  Joost J. Vlassak,et al.  Measuring the Mechanical Properties of Thin Metal Films by Means of Bulge Testing of Micromachined Windows , 1994 .