Experimental and Numerical Study of the Solid Concentration Distribution in a Horizontal Screw Decanter Centrifuge

The horizontal screw decanter centrifuge is an automatic and continuous settlement centrifuge; it is widely used in different industries. Within the centrifuge, the drum and screwpropeller rotate at different speeds in the same direction, and therefore, the fluid flow state is extremely complex. There is no theoretical method to describe the solid concentration distribution during the filtration separation process. Therefore, FLUENT software was applied to an M-2301-type horizontal screw decanter centrifuge to simulate the fluid flow situation in the centrifuge drum and obtain the solid concentration distribution. The simulation results showed that the solid volume fraction could reach 66.35 and 4.92% at the sediment outlet and the overflow outlet after 10 s of simulation, respectively, and it was in good agreement with the industrial experimental results. The research shows that the 3-D unsteady calculation combined with moving mesh is an effective technique to investigate solid concentration distributio...

[1]  Tiefeng Wang,et al.  Experimental study and numerical simulation with a coupled CFD–PBM model of the effect of liquid viscosity in a bubble column , 2013 .

[2]  J. Leahy,et al.  Characterization of compost produced from separated pig manure and a variety of bulking agents at low initial C/N ratios. , 2011, Bioresource technology.

[3]  Sourabh Kumar,et al.  Numerical simulations of heat transfer distribution of a two-pass square channel with V-rib turbulator and bleed holes , 2013 .

[4]  T. R. Bott,et al.  The role of turbulent bursts in particle re-entrainment in aqueous systems , 1989 .

[5]  Francesco Genovese,et al.  Horizontal centrifuge with screw conveyor (decanter): optimization of oil/water levels and differential speed during olive oil extraction , 2013 .

[6]  Greg Leslie,et al.  CFD simulations of membrane filtration zone in a submerged hollow fibre membrane bioreactor using a porous media approach , 2010 .

[7]  Hermann Nirschl,et al.  Multiphase CFD Simulation of a Solid Bowl Centrifuge , 2009 .

[9]  Sandra Escoffier,et al.  Using centrifuge tests data to identify the dynamic soil properties: Application to Fontainebleau sand , 2013 .

[10]  José Teixeira Freire,et al.  CFD modelling of a semi‐cylindrical spouted bed: Numerical simulation and experimental verification , 2009 .

[11]  Claudio Zilio,et al.  An assessment on air forced convection on extended surfaces: Experimental results and numerical modeling , 2013 .

[12]  Jyeshtharaj B. Joshi,et al.  Simulation of Flow in Stirred Vessels with Axial Flow Impellers: Effects of Various Numerical Schemes and Turbulence Model Parameters , 1995 .

[13]  Richard J Wakeman,et al.  Separation technologies for sludge dewatering. , 2007, Journal of hazardous materials.

[14]  N. Guan,et al.  Numerical investigation on heat transfer of liquid flow at low Reynolds number in micro-cylinder-groups , 2012 .

[15]  Laurentiu Pasol,et al.  New centrifuge pond level control system handles variable feeds , 2010 .

[16]  Akinori Furukawa,et al.  Experimental analysis of flow structure in contra-rotating axial flow pump designed with different rotational speed concept , 2013 .

[17]  Clayton J. Radke,et al.  A filtration model for the flow of dilute, stable emulsions in porous media. II: Parameter evaluation and estimation , 1986 .

[18]  Zdzisław Jaworski,et al.  THE EFFECT OF SIZE, LOCATION AND PUMPING DIRECTION OF PITCHED BLADE TURBINE IMPELLERS ON FLOW PATTERNS: LDA MEASUREMENTS AND CFD PREDICTIONS , 2001 .

[19]  Jinjia Wei,et al.  3D turbulent flow modeling in the separation column of a circumfluent cyclone , 2013 .

[20]  S G Sommer,et al.  Separation efficiency and particle size distribution in relation to manure type and storage conditions. , 2002, Bioresource technology.