A new method to detect delamination in composites using chirp-excited Lamb wave and wavelet analysis

Abstract Lamb waves offer an efficient way for monitoring the structural integrity of large carbon fiber reinforced polymer (CFRP) structures. This paper presents a new method that is able to detect and assess delamination's length in anisotropic CFRP plates. It uses a chirp signal, which contains a wide range of frequencies, as excitation. Thus the material is interrogated by Lamb waves with various wavelengths. This method is based on that, for a specific delamination length, only some particular frequency components are disturbed. Simulation and experimental results show that the lowest frequency that is perturbed by a delamination decreases as the delamination length increases. Therefore, by observing which frequency components of the chirp-exited Lamb wave are disturbed, delamination length can be estimated. Wavelet analysis is implemented for better comparison of signals at multiple frequencies.

[1]  Jing Lin,et al.  Chirp-based dispersion pre-compensation for high resolution Lamb wave inspection , 2014 .

[2]  Bo Feng,et al.  Interaction of lamb waves with the edges of a delamination in CFRP composites , 2017, 2017 IEEE International Workshop on Metrology for AeroSpace (MetroAeroSpace).

[3]  D. Greve,et al.  Generation and detection of guided waves using PZT wafer transducers , 2005, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[4]  P. Cawley,et al.  The interaction of Lamb waves with defects , 1992, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[5]  Luca De Marchi,et al.  A signal processing approach to exploit chirp excitation in Lamb wave defect detection and localization procedures , 2013 .

[6]  M. Salman Leong,et al.  Wavelet Analysis: Mother Wavelet Selection Methods , 2013 .

[7]  Chun H. Wang,et al.  Ultrasonic detection and sizing of compressed cracks in glass- and carbon-fibre reinforced plastic composites , 2017 .

[8]  Jennifer E. Michaels,et al.  Multi-mode and multi-frequency guided wave imaging via chirp excitations , 2011, Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[9]  Joseph L. Rose,et al.  Ultrasonic Guided Waves in Solid Media , 2014 .

[10]  P. Cawley,et al.  The interaction of Lamb waves with delaminations in composite laminates , 1993 .

[11]  K. Balasubramaniam,et al.  Interaction of the primary anti-symmetric Lamb mode (Ao) with symmetric delaminations: numerical and experimental studies , 2009 .

[12]  I. Genesio,et al.  Simulation of Lamb wave propagation for the characterization of complex structures , 2003, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[13]  Lin Ye,et al.  Lamb wave-based quantitative identification of delamination in CF/EP composite structures using artificial neural algorithm , 2004 .

[14]  Samir Mustapha,et al.  Concise analysis of wave propagation using the spectral element method and identification of delamination in CF/EP composite beams , 2010 .

[15]  Costas Soutis,et al.  Real-time nondestructive evaluation of fiber composite laminates using low-frequency Lamb waves. , 2002, The Journal of the Acoustical Society of America.

[16]  Mamoru Shimazaki,et al.  Delamination detection in composite laminates using dispersion change based on mode conversion of Lamb waves , 2010 .

[17]  Bin Wu,et al.  Delamination detection in composite beams using pure Lamb mode generated by air-coupled ultrasonic transducer , 2014 .

[18]  Cara A. C. Leckey,et al.  Delamination detection and quantification on laminated composite structures with Lamb waves and wavenumber analysis , 2015 .

[19]  Krishnan Balasubramaniam,et al.  Interaction of guided Lamb waves with an asymmetrically located delamination in a laminated composite plate , 2010 .

[20]  P. Wilcox,et al.  The effect of dispersion on long range inspection using ultrasonic guided waves , 2001 .

[21]  Ning Hu,et al.  Identification of delamination position in cross-ply laminated composite beams using S0 Lamb mode , 2008 .

[23]  Ruqiang Yan,et al.  Wavelets: Theory and Applications for Manufacturing , 2010 .

[24]  Bing Li,et al.  Quantitative identification of delamination at different interfaces using guided wave signals in composite laminates , 2015 .

[25]  Jan Drewes Achenbach,et al.  Group delay measurements using modally selective Lamb wave transducers for detection and sizing of delaminations in composites , 2008 .

[26]  Bin Liu,et al.  A Fatigue Crack Size Evaluation Method Based on Lamb Wave Simulation and Limited Experimental Data , 2017, Sensors.

[27]  Sang Jun Lee,et al.  Chirp excitation of ultrasonic guided waves. , 2013, Ultrasonics.

[28]  Zhongqing Su,et al.  A quantitative identification approach for delamination in laminated composite beams using digital damage fingerprints (DDFs) , 2006 .

[29]  Kazuro Kageyama,et al.  Optimal Mother Wavelet Selection for Lamb Wave Analyses , 2009 .

[30]  Krishnan Balasubramaniam,et al.  Sizing of delamination using time-of-flight of the fundamental symmetric Lamb modes , 2011 .

[31]  Hyung Jin Lim,et al.  Reference‐free delamination detection using Lamb waves , 2013 .

[32]  Takahiro Hayashi,et al.  Multiple reflections of Lamb waves at a delamination. , 2002, Ultrasonics.