Potential Use of Foamed Mortar (FM) for Thermal Upgrading of Chinese Traditional Hui-Style Residences

The Hui-style residence is an important architectural heritage of China. The hollow wall structures are widely used to build its exterior wall system. However, the thermal performance of the hollow wall is no longer able to meet the new energy-saving and environmental requirement. This article describes a laboratory study of the development of foamed mortar (FM), with the potential for use in thermal upgrading of the Hui-style hollow wall system without dramatically changing its traditional structure. The key early age, physical, mechanical and thermal properties were systematically measured. Two extended models were respectively developed to calculate compressive strength and thermal conductivity, as a function of porosity. Environment chamber test was also employed to investigate the effectiveness of this novel thermal upgrading approach and the results show that filling the voids with FM can effectively improve the overall thermal resistance of the hollow wall system by 44%, which is almost equal to the overall thermal resistance when using the more expensive commercial inorganic stucco system. In addition, the combination of these two methods yielded an overall thermal resistance of 0.701 m2·K/W, which is even higher than 0.67 m2·K/W for the code required in the hot summer/cold winter climate zone.

[1]  Peter Domone,et al.  Developments of the two-point workability test for high-performance concrete , 1999 .

[2]  I. Odler,et al.  Investigations on the relationship between porosity, structure and strength of hydrated Portland cement pastes. II. Effect of pore structure and of degree of hydration , 1985 .

[3]  Aikaterini Mccarthy,et al.  Moving Fly Ash Utilisation in Concrete Forward: A UK Perspective , 2003 .

[4]  Phaiboon Panyakapo,et al.  Reuse of thermosetting plastic waste for lightweight concrete. , 2008, Waste management.

[5]  L. Glicksman.  Heat transfer in foams , 1994 .

[6]  K. Ramamurthy,et al.  Air‐void characterisation of foam concrete , 2007 .

[7]  Martyn Jones,et al.  Utilising unprocessed low-lime coal fly ash in foamed concrete , 2005 .

[8]  Martyn Jones,et al.  Characterization and simulation of microstructure and thermal properties of foamed concrete , 2013 .

[9]  Phillip Frank Gower Banfill,et al.  The rheology of fresh mortar , 1991 .

[10]  T. Luping.  A study of the quantitative relationship between strength and pore-size distribution of porous materials , 1986 .

[11]  Moisés Frías,et al.  The pozzolanic activity of different materials, its influence on the hydration heat in mortars , 1996 .

[12]  K. Ramamurthy,et al.  A classification of studies on properties of foam concrete , 2009 .

[13]  E. Kearsley,et al.  The effect of high fly ash content on the compressive strength of foamed concrete , 2001 .

[14]  E. Kearsley,et al.  The effect of porosity on the strength of foamed concrete , 2002 .

[15]  P. G. Collishaw,et al.  An assessment of expressions for the apparent thermal conductivity of cellular materials , 1994, Journal of Materials Science.

[16]  Kimberly E. Kurtis,et al.  X-ray microtomography (microCT) of the progression of sulfate attack of cement paste , 2002 .

[17]  Kimberly E. Kurtis,et al.  Sulfate deterioration of cement-based materials examined by x-ray microtomography , 2004, SPIE Optics + Photonics.

[18]  A. Aguado,et al.  Fluidity of cement pastes with mineral admixtures and superplasticizer—A study based on the Marsh cone test , 1999 .

[19]  I. Odler,et al.  Investigations on the relationship between porosity, structure and strength of hydrated portland cement pastes I. Effect of porosity , 1985 .

[20]  M. Stampanoni,et al.  3D experimental investigation of the microstructure of cement pastes using synchrotron X-ray microtomography (μCT) , 2007 .

[21]  Nicolas Roussel,et al.  Correlation between Yield Stress and Slump: Comparison between Numerical Simulations and Concrete Rheometers Results , 2005 .

[22]  M. Ward,et al.  Effect of silica fume and fly ash on heat of hydration of Portland cement , 2002 .

[23]  G. Hoff.  Porosity-strength considerations for cellular concrete , 1972 .

[24]  B. Scheetz,et al.  Hydration of fly ash-portland cements , 1984 .

[25]  Qingyuan Wang,et al.  Online SEM investigation of microcrack characteristics of concretes at various temperatures , 2005 .

[26]  R. L. Berger,et al.  Studies on the hydration of tricalcium silicate pastes III. Influence of admixtures on hydration and strength development , 1973 .

[27]  C. Jolicoeur,et al.  Chemical admixture-cement interactions: Phenomenology and physico-chemical concepts , 1998 .

[28]  Eric Mayer,et al.  Properties Of Concrete , 2016 .

[29]  G H Tattersall,et al.  Workability and quality control of concrete , 1991 .

[30]  K. Kendall,et al.  Pore structure of cement/pozzolan composites by X-ray microtomography , 2005 .

[31]  C. Poon,et al.  Degree of hydration and gel/space ratio of high-volume fly ash/cement systems , 2000 .

[32]  A. Terauds,et al.  Evaluating the thermal conductivity of foam plastics , 1990 .

[33]  Martyn Jones,et al.  Behaviour and Assessment of Foamed Concrete for Construction Applications , 2005 .

[34]  Aikaterini Mccarthy,et al.  Potential of Foamed Concrete to Enhance the Thermal Performance of Low-Rise Dwellings , 2002 .

[35]  Azree Othuman Mydin,et al.  Thermal and mechanical properties of lightweight foamed concrete at elevated temperatures , 2012 .