EVALUATIONS OF FLOW AND MIXING EFFICIENCY IN THE KNEADING DISKS OF A NOVEL TRI-SCREW EXTRUDER

The forward or backward stagger angles of the kneading disks have great effects on configures of the special center region along axial length in a novel tri-screw extruder. In this paper, the flow and mixing of a nonNewtonian polyethylene in kneading disks of a tri-screw extruder were simulated using three-dimensional finite element modeling based on mesh superposition technique. Three types of kneading disks, neutral stagger, staggered 30° forward and staggered 30° reverse were considered for the tri-screw extruder. The effects of stagger angles of kneading disks on the flow pattern in the tri-screw extruder were investigated. Moreover, at different stagger angles, the dispersive and distributive mixing efficiencies in the kneading disks of the tri-screw extruder and the twin-screw extruder were calculated and compared by means of mean shear rate, stretching rates, maximal stress magnitudes, mixing index, residence time distribution (RTD) and logarithm of area stretch. It is found that increasing the stagger angles decreases the axial velocities of polymer melt in the center region for the tri-screw extruder. The staggered 30° reverse is relatively reasonable for the tri-screw extruder and neutral stagger for the twin-screw extruder for the mixing efficiency. In comparison, the kneading disks in the tri-screw extruder have higher distributive and dispersive mixing efficiencies than those in the twin-screw extruder with the same stagger angles.

[1]  G. Wang,et al.  Effects of Screw Clearance and Blend Ratio on The Flow and Mixing Characteristics of Tri-Screw Extruders In Cross Section With CFD , 2013 .

[2]  U. Sundararaj,et al.  Nonisothermal modeling of heat transfer inside an internal batch mixer , 2011 .

[3]  Y. Nakayama,et al.  Melt-mixing by novel pitched-tip kneading disks in a co-rotating twin-screw extruder , 2010, 1004.2273.

[4]  Mir Hamid Reza Ghoreishy,et al.  Development of an advanced computer simulation technique for the modeling of rubber curing process , 2009 .

[5]  Xianming Zhang,et al.  Numerical simulation and experimental validation of mixing performance of kneading discs in a twin screw extruder , 2009 .

[6]  C. K. Huang,et al.  Study on Kneading and Molding of PP/TiO2 Nanocomposite , 2009 .

[7]  Y. Xie,et al.  Numerical Study on Temperature and Power Consumption of Intermeshing Co-rotation Triangle Arrayed Tri-screw Extruders , 2009 .

[8]  Nan Jiang,et al.  Study on Extrusion Characteristics of the Tri-Screw Extruder , 2008 .

[9]  Mir Hamid Reza Ghoreishy,et al.  Three-dimensional Finite Element Modeling of Rubber Curing Process , 2005 .

[10]  José A. Covas,et al.  On-line monitoring of the residence time distribution along a kneading block of a twin-screw extruder , 2004 .

[11]  Vincent Legat,et al.  Parametric Study of the Mixing Efficiency in a Kneading Block Section of a Twin-screw Extruder , 2004 .

[12]  Joseph D. Wright,et al.  Study of particle trajectories, residence times and flow behavior in kneading discs of intermeshing co‐rotating twin‐screw extruders , 2004 .

[13]  Kazumori Funatsu,et al.  3-D non-isothermal flow field analysis and mixing performance evaluation of kneading blocks in a co-rotating twin srew extruder , 2001 .

[14]  Ica Manas-Zloczower,et al.  Studies of Mixing Efficiency in Batch and Continuous Mixers , 1994 .

[15]  Julio M. Ottino,et al.  A framework for description of mechanical mixing of fluids , 1981 .

[16]  K. Yasuda,et al.  Shear flow properties of concentrated solutions of linear and star branched polystyrenes , 1981 .

[17]  Song-Gui Chena,et al.  Engineering Applications of Computational Fluid Mechanics , 2017 .

[18]  Mokhtar Awang,et al.  Engineering applications of computational fluid dynamics , 2015 .

[19]  M. Durali,et al.  A Novel Aerodynamic Design Method for Centrifugal Compressor Impeller , 2014 .

[20]  X. Z. Zhu,et al.  Study of Dynamic Flow and Mixing Performances of Tri-Screw Extruders with Finite Element Method , 2013 .

[21]  W. G. Li.  Blade Exit Angle Effects on Performance of a Standard Industrial Centrifugal Oil Pump , 2011 .

[22]  W. G. Li.  BLADE EXIT ANGLE EFFECTS ON PERFORMANCE OF A STANDARD INDUSTRIAL CENTRIFUGAL OIL PUMP , 2011 .

[23]  Ghoreyshi Mir Hamid Reza,et al.  QUASI-STEADY STATE FINITE ELEMENT MODELLING OF POLYMER MELT FLOW IN AN INTERMESHING CO-ROTATING TWIN SCREW EXTRUDER , 2010 .

[24]  陈晋南,et al.  Simulation of Polymer Melt Flow Fields in Intermeshing Co-Rotating Three-Screw Extruders , 2006 .

[25]  Chen Jin-nan.  Simulation of Polymer Melt Flow Fields in Intermeshing Co-Rotating Three-Screw Extruders , 2006 .

[26]  Hu Dongdong.  SIMULATION OF 3D ISOTHERMAL FLOW IN INTERMESHING CO-ROTATING TRI-SCREW EXTRUDERS , 2004 .

[27]  Jiang Nan,et al.  Analysis of Mixing Performance in a Tri-Screw Extruder , 2001 .

[28]  K. Funatsu,et al.  Mixing mechanism of three‐tip kneading block in twin screw extruders , 2000 .