Monitoring Thermal Performance of Hollow Bricks with Different Cavity Fillers in Difference Climate Conditions

Hollow brick blocks have found widespread use in the building industry during the last decades. The increasing requirements to the thermal insulation properties of building envelopes given by the national standards in Europe led the brick producers to reduce the production of common solid bricks. Brick blocks with more or less complex systems of internal cavities replaced the traditional bricks and became dominant on the building ceramics market. However, contrary to the solid bricks where the thermal conductivity can easily be measured by standard methods, the complex geometry of hollow brick blocks makes the application of common techniques impossible. In this paper, a steady-state technique utilizing a system of two climatic chambers separated by a connecting tunnel for sample positioning is used for the determination of the thermal conductivity, thermal resistance, and thermal transmittance (U value) of hollow bricks with the cavities filled by air, two different types of mineral wool, polystyrene balls, and foam polyurethane. The particular brick block is provided with the necessary temperature- and heat-flux sensors and thermally insulated in the tunnel. In the climatic chambers, different temperatures are set. After steady-state conditions are established in the measuring system, the effective thermal properties of the brick block are calculated using the measured data. Experimental results show that the best results are achieved with hydrophilic mineral wool as a cavity filler; the worst performance exhibits the brick block with air-filled cavities.

[1]  Robert Černý,et al.  Thermal Conductivity of Mineral Wool Materials Partially Saturated by Water , 2006 .

[2]  R. Černý,et al.  Apparent Thermal Properties of Phase-Change Materials: An Analysis Using Differential Scanning Calorimetry and Impulse Method , 2013 .

[3]  Robert Černý,et al.  Experimental assessment of hygrothermal performance of an interior thermal insulation system using a laboratory technique simulating on-site conditions , 2008 .

[4]  Ning Pan,et al.  Comparing Dynamic and Static Methods for Measuring Thermal Conductive Properties of Textiles , 1998 .

[5]  Liang Fang,et al.  Optimization of concrete hollow brick using hybrid genetic algorithm combining with artificial neural networks , 2010 .

[6]  Niccolò Aste,et al.  The influence of the external walls thermal inertia on the energy performance of well insulated buildings , 2009 .

[7]  J. C. Jaeger,et al.  Conduction of Heat in Solids , 1952 .

[8]  Luai M. Al-Hadhrami,et al.  Assessment of thermal performance of different types of masonry bricks used in Saudi Arabia , 2009 .

[9]  Behdad Moghtaderi,et al.  Effect of thermal mass on the thermal performance of various Australian residential constructions systems , 2008 .

[10]  Ammar Bouchair,et al.  Steady state theoretical model of fired clay hollow bricks for enhanced external wall thermal insulation , 2008 .

[11]  Jana Mlakar,et al.  Temperature and humidity profiles in passive-house building blocks , 2013 .

[12]  Marc J. Assael,et al.  Improving the Design of Greek Hollow Clay Bricks , 2012 .

[13]  R. Černý,et al.  Application of Effective Media Theory for Determination of Thermal Properties of Hollow Bricks as a Function of Moisture Content , 2013 .

[14]  Miroslaw Zukowski,et al.  Experimental and numerical investigation of a hollow brick filled with perlite insulation , 2010 .

[15]  P. J. García Nieto,et al.  Analysis and optimization of the heat-insulating light concrete hollow brick walls design by the finite element method , 2007 .

[16]  Sylvie Lorente,et al.  Study of convective phenomena inside cavities coupled with heat and mass transfers through porous media—application to vertical hollow bricks—a first approach , 1998 .

[17]  He Yongning,et al.  Optimization of the configuration of 290 140 90 hollow clay bricks with 3-D numerical simulation by finite volume method , 2008 .

[18]  Mohamed A. Antar,et al.  Conjugate conduction-natural convection heat transfer in a hollow building block , 2009 .

[19]  Robert Černý,et al.  Hygrothermal performance study of an innovative interior thermal insulation system , 2009 .

[20]  P. J. García Nieto,et al.  Nonlinear thermal optimization of external light concrete multi-holed brick walls by the finite element method , 2008 .

[21]  R. P. Tye,et al.  An inter-comparison of a steady-state and transient methods for measuring the thermal conductivity of thin specimens of masonry materials , 2011 .

[22]  R. Černý,et al.  Experimental Assessment of Thermal Conductivity of a Brick Block with Internal Cavities Using a Semi-scale Experiment , 2013 .

[23]  Pavla Rovnaníková,et al.  Transport processes in concrete , 2002 .

[24]  M. P. Morales,et al.  Study of the geometry of a voided clay brick using rectangular perforations to optimize its thermal properties , 2011 .

[25]  Eva Vejmelková,et al.  Effect of Moisture on Thermal Conductivity of Lime-Based Composites , 2009 .

[26]  Jan Kosny,et al.  Influence of insulation configuration on heating and cooling loads in a continuously used building , 2002 .

[27]  Majed M. Alhazmy Analysis of coupled natural convection–conduction effects on the heat transport through hollow building blocks , 2006 .