Intelligent optimization and selection of machining parameters in finish turning and facing of Inconel 718

The heat-resistant super alloy material like Inconel 718 machining is an inevitable and challenging task even in modern manufacturing processes. This paper describes the genetic algorithm coupled with artificial neural network (ANN) as an intelligent optimization technique for machining parameters optimization of Inconel 718. The machining experiments were conducted based on the design of experiments full-factorial type by varying the cutting speed, feed, and depth of cut as machining parameters against the responses of flank wear and surface roughness. The combined effects of cutting speed, feed, and depth of cut on the performance measures of surface roughness and flank wear were investigated by the analysis of variance. Using these experimental data, the mathematical model and ANN model were developed for constraints and fitness function evaluation in the intelligent optimization process. The optimization results were plotted as Pareto optimal front. Optimal machining parameters were obtained from the Pareto front graph. The confirmation experiments were conducted for the optimal machining parameters, and the betterment has been proved.

[1]  Il-Hwan Kim,et al.  Real-coded genetic algorithm for machining condition optimization , 2008 .

[2]  D. E. Dimla,et al.  Neural network solutions to the tool condition monitoring problem in metal cutting—A critical review of methods , 1997 .

[3]  Wear of mixed alumina ceramic tools in high speed facing of Inconel 718 , 2007 .

[4]  Franci Cus,et al.  Optimization of cutting process by GA approach , 2003 .

[5]  Imtiaz Ahmed Choudhury,et al.  Machinability assessment of inconel 718 by factorial design of experiment coupled with response surface methodology , 1999 .

[6]  Jun Wang,et al.  Optimization of Cutting Conditions for Single Pass Turning Operations Using a Deterministic Approach , 2002 .

[7]  Ramón Quiza Sardiñas,et al.  Genetic algorithm-based multi-objective optimization of cutting parameters in turning processes , 2006, Eng. Appl. Artif. Intell..

[8]  Gurbachan S. Sekhon.  Monitoring and control of machining operations , 2013 .

[9]  E. Ezugwu.  Key improvements in the machining of difficult-to-cut aerospace superalloys , 2005 .

[10]  R. J. Kuo,et al.  Intelligent tool wear estimation system through artificial neural networks and fuzzy modeling , 1998, Artif. Intell. Eng..

[11]  N. R. Dhar,et al.  Wear behavior of uncoated carbide inserts under dry, wet and cryogenic cooling conditions in turning C-60 steel , 2006 .

[12]  Tuğrul Özel,et al.  Predictive modeling of surface roughness and tool wear in hard turning using regression and neural networks , 2005 .

[13]  J. Paulo Davim,et al.  Multi-objective optimization of cutting parameters for drilling laminate composite materials by using genetic algorithms , 2006 .

[14]  Tuğrul Özel,et al.  Prediction of flank wear by using back propagation neural network modeling when cutting hardened H-13 steel with chamfered and honed CBN tools , 2002 .

[15]  Chia-Hsiang Menq,et al.  Uncertainty analysis and variation reduction of three-dimensional coordinate metrology. Part 2: uncertainty analysis , 1999 .

[16]  Jože Balič,et al.  SELECTION OF CUTTING CONDITIONS AND TOOL FLOW IN FLEXIBLE MANUFACTURING SYSTEM , 2001 .

[17]  P. E. Amiolemhen,et al.  Application of genetic algorithms—determination of the optimal machining parameters in the conversion of a cylindrical bar stock into a continuous finished profile , 2004 .

[18]  Wen-Tung Chien,et al.  The investigation on the prediction of tool wear and the determination of optimum cutting conditions in machining 17-4PH stainless steel , 2003 .

[19]  Kalyanmoy Deb,et al.  Multi-objective optimization using evolutionary algorithms , 2001, Wiley-Interscience series in systems and optimization.

[20]  M. S. Shunmugam,et al.  Multi-objective optimization of wire-electro discharge machining process by Non-Dominated Sorting Genetic Algorithm , 2005 .

[21]  R. Saravanan,et al.  Machining Parameters Optimisation for Turning Cylindrical Stock into a Continuous Finished Profile Using Genetic Algorithm (GA) and Simulated Annealing (SA) , 2003 .

[22]  Franci Cus,et al.  Approach to optimization of cutting conditions by using artificial neural networks , 2006 .

[23]  Tuğrul Özel,et al.  Multi-objective optimization for turning processes using neural network modeling and dynamic-neighborhood particle swarm optimization , 2007 .

[24]  M. Liang,et al.  Integration of Cutting Parameter Selection and Tool Adjustment Decisions for Multipass Turning , 2001 .

[25]  Kourosh Danai.  Machine Tool Monitoring and Control , 2001 .

[26]  A. Molinari,et al.  Modeling of tool wear by diffusion in metal cutting , 2002 .

[27]  Robert J. Schalkoff,et al.  Artificial neural networks , 1997 .

[28]  Tuğrul Özel,et al.  Finite element modeling the influence of edge roundness on the stress and temperature fields induced by high-speed machining , 2007 .

[29]  Matthias Ehrgott,et al.  Multicriteria Optimization , 2005 .

[30]  E. Ezugwu,et al.  An overview of the machinability of aeroengine alloys , 2003 .