Correlation of foodstuffs with ethanol–water mixtures with regard to the solubility of migrants from food contact materials

Today most foods are available in a packed form. During storage, the migration of chemical substances from food packaging materials into food may occur and may therefore be a potential source of consumer exposure. To protect the consumer, standard migration tests are laid down in Regulation (EU) No. 10/2011. When using those migration tests and applying additional conservative conventions, estimated exposure is linked with large uncertainties including a certain margin of safety. Thus the research project FACET was initiated within the 7th Framework Programme of the European Commission with the aim of developing a probabilistic migration modelling framework which allows one (1) to calculate migration into foods under real conditions of use; and (2) to deliver realistic concentration estimates for consumer exposure modelling for complex packaging materials (including multi-material multilayer structures). The aim was to carry out within the framework of the FACET project a comprehensive systematic study on the solubility behaviour of foodstuffs for potentially migrating organic chemicals. Therefore a rapid and convenient method was established to obtain partition coefficients between polymer and food, KP/F. With this method approximately 700 time-dependent kinetic experiments from spiked polyethylene films were performed using model migrants, foods and ethanol–water mixtures. The partition coefficients of migrants between polymer and food (KP/F) were compared with those obtained using ethanol–water mixtures (KP/F’s) to investigate whether an allocation of food groups with common migration behaviour to certain ethanol–water mixtures could be made. These studies have confirmed that the solubility of a migrant is mainly dependent on the fat content in the food and on the ethanol concentration of ethanol–water mixtures. Therefore dissolution properties of generic food groups for migrants can be assigned to those of ethanol–water mixtures. All foodstuffs (including dry foods) when allocated to FACET model food group codes can be classified into a reduced number of food categories each represented by a corresponding ethanol–water equivalency.

[1]  C. O'Mahony,et al.  Estimates of Dietary Exposure to Bisphenol A (BPA) from Light Metal Packaging using Food Consumption and Packaging usage Data: A Refined Deterministic Approach and a Fully Probabilistic (FACET) Approach , 2013, Food additives & contaminants. Part A, Chemistry, analysis, control, exposure & risk assessment.

[2]  R. Franz,et al.  Migration of plastic constituents , 2008 .

[3]  A. Hart,et al.  Approach to stochastic modelling of consumer exposure for any substance from canned foods using simulant migration data , 2006, Food additives and contaminants.

[4]  R. Franz,et al.  Migration modelling from food-contact plastics into foodstuffs as a new tool for consumer exposure estimation , 2005, Food additives and contaminants.

[5]  Simoneau Catherine,et al.  FINAL REPORT (Synthetic Version) EU Project QLK1-CT2002-2390 Foodmigrosure , 2008 .

[6]  Laurence Castle,et al.  Exposure to Substances from Food Contact Materials and an Introduction to the FACET Project , 2009 .

[7]  P K T Oldring,et al.  Development of a new modelling tool (FACET) to assess exposure to chemical migrants from food packaging , 2014, Food additives & contaminants. Part A, Chemistry, analysis, control, exposure & risk assessment.

[8]  Simoneau Catherine,et al.  Proceedings of Closing Conference of the EU Project "Foodmigrosure" Qrlt-2001-2390 - Modelling Migration from Plastics into Foodstuffs as a Novel and Cost Efficient Tool for Estimation of Consumer Exposure from Food Contacts Materials , 2008 .

[9]  P Mercea,et al.  Migration modelling as a tool for quality assurance of food packaging , 2002, Food additives and contaminants.

[10]  J. Westwater,et al.  The Mathematics of Diffusion. , 1957 .

[11]  I. Cooper,et al.  Feasibility study for the development of certified reference materials for specific migration testing. Part 1: Initial migrant concentration and specific migration , 2004, Food additives and contaminants.

[12]  P Northing,et al.  New hierarchical classification of food items for the assessment of exposure to packaging migrants: use of hub codes for different food groups , 2009, Food additives & contaminants. Part A, Chemistry, analysis, control, exposure & risk assessment.

[13]  Y. Kawamura,et al.  Determination of additives in food contact polypropylene , 2000 .

[14]  Angela Störmer,et al.  Correlation between Partition Coefficients Polymer/Food Simulant, KP,F, and Octanol/Water, Log POW ― a New Approach in support of Migration Modeling and Compliance Testing , 2010 .