Modeling and experimental investigations on the drag reduction performance of an axial oscillation tool

Abstract The high friction of a drill string against a wellbore is a concern during directional and horizontal drilling. An axial oscillation tool (AOT) is typically used to reduce drag and torque. This study examined the axial oscillation drag reduction mechanism using a specially designed laboratory test rig. An indoor simulation experiment was conducted, followed by model recognition and identification of the friction model parameters based on the experimental data. A torque/drag model and drilling string axial vibration model were used to establish the numerical model. Additionally, the boundary condition between the drill pipe and wellbore was based on a nonlinear dynamic friction model. Finally, the model was solved using a numerical method to gain an understanding of the drag reduction mechanism of the axial oscillation tool. The indoor experiment of the nonlinear friction model revealed that the Coulomb friction model appeared to disagree with the measured data of the experiment. The nonlinear dynamic friction model, however, which was based on the acquired parameters using particle swarm optimization (PSO), yielded results that were in good agreement with the experimental results. Comparisons with experimental setups, data and models from the literature were conducted. The simulation results clearly demonstrated that the friction reduction was effective when the amplitudes of the vibration velocities exceeded the drive velocity. Decreasing the slip velocity of drill strings and increasing the amplitude of the axial oscillation tool vibration force effectively lengthened the drilling-string vibration range. Furthermore, the optimal position of the axial oscillation tool corresponded to a highly deviated well section that was characterized by the existence of high friction resistance. Therefore, the oscillation motion of the drill pipe at a highly deviated well section could significantly decrease the total friction force of the entire drill string.

[1]  P. Dahl.  A Solid Friction Model , 1968 .

[2]  Jörg Wallaschek,et al.  Sliding friction in the presence of ultrasonic oscillations: superposition of longitudinal oscillations , 2001 .

[3]  Mariusz Leus,et al.  Computational model for friction force estimation in sliding motion at transverse tangential vibrations of elastic contact support , 2015 .

[4]  H. Ho,et al.  An Improved Modeling Program for Computing the Torque and Drag in Directional and Deep Wells , 1988 .

[5]  Bernt S. Aadnøy,et al.  Design of oil wells using analytical friction models , 2001 .

[6]  Mariusz Leus,et al.  Analysis of longitudinal tangential contact vibration effect on friction force using Coulomb and Dahl models , 2008 .

[7]  C. A. Johancsik,et al.  Torque and drag in directional wells-prediction and measurement , 1983 .

[8]  Zhenhua Rui,et al.  A new method to determine Biot's coefficients of Bakken samples , 2014 .

[9]  Deli Gao,et al.  A review of down-hole tubular string buckling in well engineering , 2015, Petroleum Science.

[10]  Xiaoliang Zhao,et al.  A simulation method for modified isochronal well testing to determine shale gas well productivity , 2015 .

[11]  Z Li.  Fundamental equations and its applications for dynamical analysis of rod and pipe string in oil and gas wells. , 1999 .

[12]  Vadim S. Tikhonov,et al.  Analysis of Postbucking Drillstring Vibrations in Rotary Drilling of Extended-Reach Wells , 2009 .

[13]  Xinwei Liao,et al.  Case studies on the CO2 storage and EOR in heterogeneous, highly water-saturated, and extra-low permeability Chinese reservoirs , 2016 .

[14]  Ryan Gee,et al.  Axial Oscillation Tools vs. Lateral Vibration Tools for Friction Reduction – What's the Best Way to Shake the Pipe? , 2015 .

[15]  Hamid D. Taghirad,et al.  Modeling and Parameter Identification of Harmonic Drive Systems , 1998 .

[16]  C. H. Tseng,et al.  The effect of friction reduction in the presence of in-plane vibrations , 2006 .

[17]  Qingsong Xu,et al.  Dahl Model-Based Hysteresis Compensation and Precise Positioning Control of an XY Parallel Micromanipulator With Piezoelectric Actuation , 2010 .

[18]  Robello Samuel,et al.  How Good Is the Torque/Drag Model? , 2009 .

[19]  Vadim S. Tikhonov,et al.  Analysis of Postbuckling Drillstring Vibrations in Rotary Drilling of Extended-Reach Wells , 2011 .

[20]  F. Al-Bender,et al.  Comparison of model and non-model based friction compensation techniques in the neighbourhood of pre-sliding friction , 2004, Proceedings of the 2004 American Control Conference.

[21]  A. Soom,et al.  Normal Vibrations and Friction Under Harmonic Loads: Part I—Hertzian Contacts , 1991 .

[22]  Static friction processes under dynamic loads and vibration , 1982 .

[23]  Ning-ning Zhou,et al.  Experimental study of air squeeze effect on high-frequency friction contact , 2010 .

[24]  R. Pohlman,et al.  Influence of ultrasonic vibration on metallic friction , 1966 .

[25]  Yang Liu,et al.  Modeling friction-reducing performance of an axial oscillation tool using dynamic friction model , 2016 .

[26]  B. Walczak,et al.  Particle swarm optimization (PSO). A tutorial , 2015 .

[27]  J. Wallaschek,et al.  The effect of friction reduction in presence of ultrasonic vibrations and its relevance to travelling wave ultrasonic motors. , 2002, Ultrasonics.

[28]  D. Godfrey.  Vibration Reduces Metal to Metal Contact and Causes an Apparent Reduction in Friction , 1967 .

[29]  Qiang Han,et al.  The mechanical properties of shale based on micro-indentation test , 2015 .

[30]  Mariusz Leus,et al.  The effect of longitudinal tangential vibrations on friction and driving forces in sliding motion , 2012 .

[31]  Andrew S. Zheng,et al.  Modeling and Field Trials of the Effective Tractoring Force of Axial Vibration Tools , 2014 .

[32]  Curtis Cheatham,et al.  Dynamic Model for Stiff-String Torque and Drag (see associated supplementary discussion) , 2014 .

[33]  R. Clough,et al.  Dynamics Of Structures , 1975 .

[34]  I. Hutchings,et al.  Reduction of the sliding friction of metals by the application of longitudinal or transverse ultrasonic vibration , 2004 .

[35]  Deli Gao,et al.  Study on multi-segment friction factors inversion in extended-reach well based on an enhanced PSO model , 2015 .

[36]  Xinwei Liao,et al.  The qualitative and quantitative fracture evaluation methodology in shale gas reservoir , 2015 .

[37]  T. Piatkowski,et al.  Dahl and LuGre dynamic friction models — The analysis of selected properties , 2014 .

[38]  X. Pang,et al.  Petroleum geology features and research developments of hydrocarbon accumulation in deep petroliferous basins , 2015, Petroleum Science.

[39]  Riccardo Poli,et al.  Particle swarm optimization , 1995, Swarm Intelligence.

[40]  John L. Thorogood,et al.  A Compendium of Directional Calculations Based on the Minimum Curvature Method , 2005 .

[41]  Hans D. Fridman,et al.  Reduction of Static Friction by Sonic Vibrations , 1959 .

[42]  Qiang Han,et al.  Influencing factor analysis of shale micro-indentation measurement , 2015 .

[43]  Curtis Cheatham,et al.  Dynamic Model for Stiff String Torque and Drag , 2013 .

[44]  K. Park.  An Improved Stiffly Stable Method for Direct Integration of Nonlinear Structural Dynamic Equations , 1975 .

[45]  Ray Rui,et al.  Multi-index and two-level evaluation of shale gas reserve quality , 2016 .

[46]  Phil R Dahl,et al.  Measurement of Solid Friction Parameters of Ball Bearings , 1977 .

[47]  Robert Kostek,et al.  Influence of normal micro-vibrations in contact on sliding motion of solid body , 2005 .

[48]  Bjørnar Lund,et al.  New Downhole Tool for Coiled Tubing Extended Reach , 2000 .

[49]  Robello Samuel,et al.  Friction factors: What are they for torque, drag, vibration, bottom hole assembly and transient surge/swab analyses? , 2010 .

[50]  Chen Guangxiong,et al.  Effect of surface topography on formation of squeal under reciprocating sliding , 2002 .

[51]  Robert F. Mitchell,et al.  Drillstring Analysis With a Discrete Torque/Drag Model , 2015 .

[52]  Wang Yong,et al.  Experimental investigation of the effect of in-plane vibrations on friction for different materials , 2016 .

[53]  Weiping Zhu,et al.  Dynamic characteristics analysis of drillstring in the ultra-deep well with spatial curved beam finite element , 2012 .

[54]  Kenneth Ray Newman,et al.  Modeling the Affect of a Downhole Vibrator , 2009 .

[55]  David S. Schechter,et al.  An integrated workflow for characterization and simulation of complex fracture networks utilizing microseismic and horizontal core data , 2016 .

[56]  J. Klafter,et al.  The nonlinear nature of friction , 2004, Nature.