Sodium silicate-based, alkali-activated slag mortars: Part I. Strength, hydration and microstructure

Alkali activation of ground granulated blast furnace slag (GGBFS) with sodium silicate gave clinker-free binders, with high strength and early strength development, although set times were short and somewhat variable. Isothermal calorimetry detected three heat evolution peaks (wetting, gelation of activator and bulk reaction of slag). X-ray diffraction (XRD) showed no crystalline products. Hydration was investigated by scanning electron microscopy (SEM; with quantitative image analysis) and 29Si magic angle spinning nuclear magnetic resonance (MAS NMR). From early age, a uniform gel filled the initially water-filled space, and gradually densified as reaction proceeded. Microanalysis of outer product (OP) showed an Al-substituted C–S–H gel phase of widely variable (0.5–1.0) Ca/Si ratio. NMR showed long-chain substituted C–S–H with Al/Si ratio rising to 0.19 at 1 year, and also cross-linked material, consistent with a Ca- or Al-modified silica gel. Inner product (IP) regions around slag grains probably also contained hydrotalcite. Activation with KOH gave more rapid reaction of slag than for silicate activation, a less homogeneous microstructure, and lower strengths. The hydrates contained a substituted C–S–H gel of low Ca/Si ratio probably mixed with hydrotalcite, and occasional higher Al regions in the OP regions.

[1]  K. Scrivener,et al.  Hydration products of alkali activated slag cement , 1995 .

[2]  C. Dobson,et al.  The characterization of hardened alkali-activated blast-furnace slag pastes and the nature of the calcium silicate hydrate (C-S-H) phase , 1994 .

[3]  V. M. Malhotra,et al.  Properties and Durability of Alkali-Activated Slag Concrete , 1992 .

[4]  I. Richardson,et al.  The incorporation of minor and trace elements into calcium silicate hydrate (CSH) gel in hardened cement pastes , 1993 .

[5]  H. Taylor,et al.  Microstructure and Microchemistry of Slag Cement Pastes , 1986 .

[6]  P. L. Pratt,et al.  Factors affecting the strength of alkali-activated slag , 1994 .

[7]  J. Sykes,et al.  Sodium silicate-based alkali-activated slag mortars: Part II. The retarding effect of additions of sodium chloride or malic acid , 2000 .

[8]  H. Taylor.  Proposed Structure for Calcium Silicate Hydrate Gel , 1986 .

[9]  P. L. Pratt,et al.  Quantitative characterization of the transition zone in high strength concretes , 1988 .

[10]  E. Douglas,et al.  A preliminary study on the alkali activation of ground granulated blast-furnace slag , 1990 .

[11]  P. L. Pratt,et al.  Alkali-activated slag cement and concrete: a review of properties and problems , 1995 .

[12]  D. Roy.  Alkali-activated cements Opportunities and challenges , 1999 .

[13]  A. Atkinson,et al.  Automated identification of the aggregate–paste interfacial transition zone in mortars of silica sand with Portland or alkali-activated slag cement paste , 2000 .

[14]  S. Sarkar,et al.  Strength and Microstructural Properties of Water Glass Activated Slag , 1991 .

[15]  I. Richardson,et al.  The structure of the calcium silicate hydrate phases present in hardened pastes of white Portland cement/blast-furnace slag blends , 1997 .

[16]  Shao-dong Wang,et al.  Review of recent research on alkali-activated concrete in China , 1991 .

[17]  J. E. Gillott,et al.  Freeze-Thaw Durability of ActivatedBlast Furnace Slag Cement Concrete , 1996 .

[18]  Shao-dong Wang.  Alkaline activation of slag , 1995 .

[19]  J. E. Gillott,et al.  Alkali-silica reaction (ASR) and alkali-carbonate reaction (ACR) in activated blast furnace slag cement (ABFSC) concrete , 1996 .

[20]  V. Malhotra,et al.  Alkali activated ground granulated blast-furnace slag concrete: Preliminary investigation , 1991 .

[21]  C. Dobson,et al.  Location of Aluminum in Substituted Calcium Silicate Hydrate (C‐S‐H) Gels as Determined by 29Si and 27Al NMR and EELS , 1993 .