The Theory of Plasticity: A Survey of Recent Achievements

After a brief historical introduction, recent achievements in the theory of plasticity are surveyed with emphasis on applications in mechanical engineering.Kinematic models are presented that indicate the complexities of mechanical behaviour in the plastic range. The fundamental theorems of limit analysis are discussed, and their application to two- and three-dimensional problems is illustrated by examples. Shakedown analysis and limit design are defined. Problems involving large plastic deformations are discussed with special reference to metal forming processes. Applications of the theory of plasticity to impact testing and blast damage are reviewed. Recent changes in the theory of structural stability in the plastic range are mentioned. Throughout the lecture, impending developments of the theory of plasticity are indicated.

[1]  W. Rankine.  II. On the stability of loose earth , 1857, Philosophical Transactions of the Royal Society of London.

[2]  Rodney Hill,et al.  On the limits set by plastic yielding to the intensity of singularities of stress , 1954 .

[3]  H. Ziegler,et al.  Linear elastic stability , 1953 .

[4]  Ernst Melan,et al.  Zur Plastizität des räumlichen Kontinuums , 1938 .

[5]  Richard Von Mises,et al.  Mechanik der plastischen Formänderung von Kristallen , 1928 .

[6]  W. Prager,et al.  The Necking of a Tension Specimen in Plane Plastic Flow , 1954 .

[7]  J. Foulkes,et al.  The minimum-weight design of structural frames , 1954, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[8]  Rodney Hill.  Relations between roll‐force, torque, and the applied tensions in strip‐rolling* * Paper No. MW/A/44/48 of the Rolling Committee of the British Iron and Steel Research Association. , 1950 .

[9]  W. M. Shepherd,et al.  An Experimental Investigation of Plastic Stress—Strain Relations , 1950 .

[10]  H. J. Greenberg,et al.  EXTENDED LIMIT DESIGN THEOREMS FOR CONTINUOUS MEDIA , 1952 .

[11]  P. Symonds,et al.  Plastic Deformation in Beams under Distributed Dynamic Loads , 1954 .

[12]  J.F.W. Bishop,et al.  On the complete solution to problems of deformation of a plastic-rigid material , 1953 .

[13]  A. Nádai.  Über die Gleit- und Verzweigungsflächen einiger Gleichgewichtszustände bildsamer Massen und die Nachspannungen bleibend verzerrter Körper , 1924 .

[14]  P. Symonds.  On the general equations of problems of axial symmetry in the theory of plasticity , 1949 .

[15]  W. Prager,et al.  A Variational Principle for Plastic Materials with Strain-Hardening , 1948 .

[16]  J. Heyman.  Plastic design of beams and plane frames for minimum material consumption , 1951 .

[17]  T. Kármán,et al.  8. Beitrag zur Theorie des Walzvorganges , 1925 .

[18]  G. Taylor,et al.  THE FORMATION AND ENLARGEMENT OF A CIRCULAR HOLE IN A THIN PLASTIC SHEET , 1948 .

[19]  A. Reuss,et al.  Berücksichtigung der elastischen Formänderung in der Plastizitätstheorie , 1930 .

[20]  Thermal and Creep Effects in Work-Hardening Elastic-Plastic Solids , 1954 .

[21]  A. L. Nadai.  The Flow of Metals under Various Stress Conditions , 1947 .

[22]  W. Prager,et al.  On the mechanical behaviour of metals in the strain-hardening range , 1947 .

[23]  R. Hill.  The mathematical theory of plasticity , 1950 .

[24]  Hugh Ford,et al.  The Calculation of Roll Force and Torque in Cold Strip Rolling with Tensions , 1948 .

[25]  D. R. Bland.  A Theoretical Investigation of Roll Flattening , 1950 .

[26]  F. A. Gaydon.  On the yield-point loading of a square plate with concentric circular hole , 1954 .

[27]  Geoffrey Ingram Taylor,et al.  The use of flat-ended projectiles for determining dynamic yield stress I. Theoretical considerations , 1948, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[28]  G. Taylor.  A connexion between the criterion of yield and the strain ratio relationship in plastic solids , 1947, Proceedings of the Royal Society of London. Series A, Mathematical and physical sciences.

[29]  F. Dimaggio,et al.  On the development of plastic hinges in rigid-plastic beams , 1953 .

[30]  The theory of plasticity in relation to its engineering applications , 1954 .

[31]  W. Prager,et al.  Problem Types in the Theory of Perfectly Plastic Materials , 1948 .

[32]  Rodney Hill,et al.  On the mechanics of cutting metal strips with knife-edged tools , 1953 .

[33]  S. J. Tupper,et al.  The theory of combined plastic and elastic deformation with particular reference to a thick tube under internal pressure , 1947, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[34]  A. P. Green.  THE PLASTIC YIELDING OF NOTCHED BARS DUE TO BENDING , 1953 .

[35]  S. J. Tupper,et al.  The theory of wedge indentation of ductile materials , 1947, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[36]  Rodney Hill,et al.  On the plastic distortion of solid bars by combined bending and twisting , 1953 .

[37]  A. Nádai.  Der Beginn des Fließvorganges in einem tordierten Stab , 1923 .

[38]  L. Prandtl,et al.  Anwendungsbeispiele zu einem Henckyschen Satz über das plastische Gleichgewicht , 1923 .

[39]  Pol Duwez,et al.  The Propagation of Plastic Deformation in Solids , 1950 .

[40]  K. Hohenemser,et al.  Beitrag zur Mechanik des bildsamen Verhaltens von Flußstahl , 1932 .

[41]  R. Hill,et al.  C. A theory of the plastic bulging of a metal diaphragm by lateral pressure , 1950 .

[42]  R. B. Sims,et al.  A Note on the Theory of Rolling with Tensions , 1953 .

[43]  W. Prager,et al.  The Bursting Speed of a Rotating Plastic Disc , 1954 .

[44]  L. E. Malvern.  Plastic wave propagation in a bar of material exhibiting a strain rate effect , 1951 .

[45]  Plastic flow in a deeply notched bar with semi-circular root , 1954 .

[46]  R. Hill,et al.  THE PLASTIC YIELDING OF NOTCHED BARS UNDER TENSION , 1949 .

[47]  A. P. Green.  On the use of hodographs in problems of plane plastic strain , 1954 .

[48]  Chintsun Hwang,et al.  Plastic Collapse of Thin Rings , 1953 .

[49]  J. Foulkes.  Minimum weight design and the theory of plastic collapse , 1953 .

[50]  An analysis of the plastic bending of a thin strip in its plane , 1953 .

[51]  H Geiringer.  Simple Waves in the Complete General Problem of Plasticity Theory. , 1951, Proceedings of the National Academy of Sciences of the United States of America.

[52]  J. Craggs,et al.  Wave motion in plastic-elastic strings , 1954 .

[53]  E. Orowan,et al.  The Calculation of Roll Pressure in Hot and Cold Flat Rolling , 1943 .

[54]  William Prager,et al.  Limit analysis of arches , 1953 .

[55]  A theoretical investigation of the yield point loading of a square plate with a central circular hole , 1954 .

[56]  Kalman J. Dejuhasz.  Graphical analysis of impact of bars stressed above the elastic range , 1949 .

[57]  W. Prager.  Fundamental theorems of a new mathematical theory of plasticity , 1942 .

[58]  Rodney Hill,et al.  LXXXVIII. On the state of stress in a plastic-rigid body at the yield point , 1951 .

[59]  W. Prager.  Theory of plastic flow versus theory of plastic deformation , 1948 .

[60]  E. H. Lee.  L. On the significance of the limit load theorems for an elastic-plastic body , 1952 .

[61]  H. W. Swift.  LXXXI. Stresses and strains in tube-drawing , 1949 .

[62]  Hugh Ford,et al.  Researches into the Deformation of Metals by Cold Rolling , 1948 .

[63]  N. J. Hoff,et al.  Forty-First Wilbur Wright Memorial Lecture: Buckling and Stability , 1954, The Journal of the Royal Aeronautical Society.

[64]  P. Symonds,et al.  Impact of finite beams of ductile metal , 1954 .

[65]  E. Lee,et al.  A boundary value problem in the theory of plastic wave propagation , 1953 .

[66]  William Prager,et al.  The load carrying capacities of circular plates , 1953 .

[67]  Rodney Hill,et al.  A VARIATIONAL PRINCIPLE OF MAXIMUM PLASTIC WORK IN CLASSICAL PLASTICITY , 1948 .