Effect of post-homogenisation cooling rate and Mn addition on Mg2Si precipitation and hot workability of AA6060 alloys

ABSTRACT The microstructure evolution for different post-homogenisation cooling rates and the flow stress behaviour in direct chill cast AA6060 alloys were studied. Results revealed that decreasing cooling rates reduced the flow stress owing to the precipitation of Mg2Si and reduction of the solid solution level. Micro-alloying of Mn generated a distribution of α-Al(FeMn)Si dispersoids during the homogenisation, with the size and number density decreasing at higher homogenisation temperatures. TEM studies confirmed that the dispersoids acted as favourable nucleation sites for Mg2Si and significantly promoted the precipitation of Mg2Si during subsequent cooling. The high-temperature flow stress was controlled by the solid solution levels of Mg, Si, and Mn resulting from the interaction between dispersoids and Mg2Si. The combination of the Mn addition, a low cooling rate, and a low homogenisation temperature provided the lowest flow stress, which improved the hot workability of the alloy and promoted ready dissolution of Mg2Si during extrusion.

[1]  N. Parson,et al.  Effect of Homogenization Treatment and Microalloying with Mn on the Microstructure and Hot Workability of AA6060 Aluminum Alloys , 2019, Journal of Materials Engineering and Performance.

[2]  Z. H. Li,et al.  Microstructure, elevated-temperature mechanical properties and creep resistance of dispersoid-strengthened Al-Mn-Mg 3xxx alloys with varying Mg and Si contents , 2017 .

[3]  Chenglu Liu.  Microstructure evolution during homogenization and its effect on the high temperature deformation behaviour in AA6082 based alloys , 2017 .

[4]  Zhan Zhang,et al.  Effect of magnesium on dispersoid strengthening of Al—Mn—Mg—Si (3xxx) alloys , 2016 .

[5]  S. Spigarelli,et al.  Mechanical Properties and Microstructure of Primary and Secondary AA6063 Aluminum Alloy after Extrusion and T5 Heat Treatment , 2015 .

[6]  X. Chen,et al.  Effect of vanadium on hot deformation and microstructural evolution of 7150 aluminum alloy , 2014 .

[7]  Y. Birol.  Effect of homogenisation cooling rate and press exit temperature on extrudability and T5 hardness of EN AW 6082 alloy , 2013 .

[8]  Y. Birol.  Effect of cooling rate on precipitation during homogenization cooling in an excess silicon AlMgSi alloy , 2012 .

[9]  Qinglong Zhao,et al.  Comparison of the influence of Si and Fe in 99.999% purity aluminum and in commercial-purity aluminum , 2012 .

[10]  E. Evangelista.  Hot Deformation and Processing of Aluminum Alloys , 2011 .

[11]  Qing Liu,et al.  Dispersoid Formation and Recrystallization Behavior in an Al-Mg-Si-Mn Alloy , 2010 .

[12]  O. Sherby,et al.  Rate-controlling processes in creep of subgrain containing aluminum materials , 2005 .

[13]  O. Sherby,et al.  Solute-diffusion-controlled dislocation creep in pure aluminium containing 0.026 at.% Fe , 2004 .

[14]  M. Kral,et al.  Identification of intermetallic phases in a eutectic Al–Si casting alloy using electron backscatter diffraction pattern analysis , 2004 .

[15]  Y. Birol.  The effect of homogenization practice on the microstructure of AA6063 billets , 2004 .

[16]  O. Reiso.  Extrusion of AlMgSi Alloys , 2004 .

[17]  Fred J. Vermolen,et al.  A Model of the β-AlFeSi to α-Al(FeMn)Si Transformation in Al-Mg-Si Alloys , 2003 .

[18]  J. Kaufman.  Introduction to Aluminum Alloys and Tempers , 2000 .

[19]  J. V. Langkruis.  The effect of thermal treatments on the extrusion behaviour of AlMgSi alloys , 2000 .

[20]  N. Ryum,et al.  Precipitation of dispersoids containing Mn and/or Cr in Al-Mg-Si-alloys , 2000 .

[21]  S. Nam,et al.  Enhancement of mechanical properties of Al–Mg–Si alloys by means of manganese dispersoids , 1999 .

[22]  Joseph R. Davis,et al.  Special Features of Structure Formation and Properties of Special High-Alloy Alloys of the Al – Si – Cu System , 2023, Metal Science and Heat Treatment.

[23]  E. A. Starke,et al.  Aluminum alloys their physical and mechanical properties , 1986 .

[24]  J. Martin,et al.  The effects of dispersoids upon the micromechanisms of crack propagation in AlMgSi alloys , 1979 .