Lightweight design of carbon twill weave fabric composite body structure for electric vehicle

Design of composite appears more challenging compared with metallic counterparts because of its microstructural heterogeneity and behavioral sophistication. This paper aims to develop a multiscale approach for predicting three-dimensional elastic model of carbon twill weave fabric composite which will be applied to crashworthiness analysis of body structure of electric vehicle. The geometric parameters were obtained by measuring the microstructure of T300 carbon twill weave fabric composite through optical microscopy. The finite element model of representative volume element (RVE) in laminate composite was established to characterize the elastic properties of the materials using the homogenization technique. The numerical results of property were compared with those from uniaxial tensile and three point bending tests. Finally, the constitutive model of such composite was employed to crashworthiness analysis for electric vehicle body structure under the roof crash and side pole impact. The study indicates that the deformation behaviors of laminate calculated by using the elastic properties are in good agreement with tensile and bending experimental results with maximum relative errors of 4.04% and 7.79%, respectively. Meanwhile, a 28% savings of body weight is achieved using the carbon twill weave fabric composite compared to its predecessor made of glass fiber reinforced plastics (GFRP).

[1]  Giovanni Belingardi,et al.  Lightweight design and crash analysis of composite frontal impact energy absorbing structures , 2012 .

[2]  H. Hadavinia,et al.  Effect of delamination failure in crashworthiness analysis of hybrid composite box structures , 2010 .

[3]  Uday K. Vaidya,et al.  Thermoplastic sandwich structure design and manufacturing for the body panel of mass transit vehicle , 2007 .

[4]  Amanda Jacob.  BMW counts on carbon fibre for its Megacity Vehicle , 2010 .

[5]  Dimitrios E. Manolakos,et al.  On the response of thin-walled CFRP composite tubular components subjected to static and dynamic axial compressive loading: experimental , 2005 .

[6]  F. Field,et al.  Strategic Materials Selection In The Automobile Body: Economic Opportunities for Polymer Composite Design , 2008 .

[7]  Uday K. Vaidya,et al.  Design and development of thermoplastic composite roof door for mass transit bus , 2009 .

[8]  Chad A. Ulven,et al.  Design and Development of a Long Fiber Thermoplastic Bus Seat , 2006 .

[9]  Michael R. Bambach,et al.  Composite steel–CFRP SHS tubes under axial impact , 2009 .

[10]  Uday K. Vaidya,et al.  Process simulation, design and manufacturing of a long fiber thermoplastic composite for mass transit application , 2008 .

[11]  H. Hamada,et al.  Energy Absorption Capability of 3D Braided-Textile Composite Tubes with Rectangular Cross Section , 2007 .

[12]  E. Deletombe,et al.  Study of the influence of the number of inter-ply interfaces on the bearing rupture of riveted composite assemblies , 2008 .

[13]  S. Sarkar,et al.  Strength and fracture behavior of two-, three- and four-dimensionally reinforced carbon/carbon composites , 2010 .

[14]  Raimund Rolfes,et al.  Multiscale progressive failure analysis of textile composites , 2010 .

[15]  Uday K. Vaidya,et al.  Design and Manufacture of Woven Reinforced Glass/Polypropylene Composites for Mass Transit Floor Structure , 2004 .

[16]  Andrea Prota,et al.  Multiscale approach for the design of composite sandwich structures for train application , 2010 .

[17]  I. Yang,et al.  Optimal crashworthiness design of CFRP hat shaped section member under axial impact , 2011 .

[18]  Paolo Feraboli,et al.  Development of carbon/epoxy structural components for a high performance vehicle , 2004 .

[19]  Sun-Pui Ng,et al.  Numerical and experimental determination of in-plane elastic properties of 2/2 twill weave fabric composites , 1998 .

[20]  Uday K. Vaidya,et al.  Design, manufacture and analysis of a thermoplastic composite frame structure for mass transit , 2007 .