Impurity features in Ni-YSZ-H2-H2O electrodes

Abstract The impurity content of previously electrochemically characterized patterned Ni anodes for SOFC (solid oxide fuel cells) has been analyzed with a combination of SEM (scanning electron microscopy), AFM (atomic force microscopy), XPS (X-ray photoelectron spectroscopy) and TOF-SIMS (time-of-flight secondary ion mass spectrometry). This analysis yields comprehensive information on composition and lateral distribution of impurity species as well as the size of impurity features. Small impurity striations are found at the triple phase boundary (TPB) as well as on the former electrode–electrolyte interface and the impurity features were found to be influenced by the electrode configuration and the initial behavior of the Ni electrode during thermal exposure (creep or shrinkage). Furthermore, the electrochemical performance (the line specific resistance LSR) was compared to data reported for Ni point anodes. Good agreement was obtained for data with comparable impurity features. Additionally, an order of magnitude estimation of the effect of SiO 2 content on surface coverage with an impurity film is performed for different electrode designs (point, patterned and cermet anode) and shows different preconditions for model anodes and nano- or microstructured cermet anodes. With typical impurity levels, a complete coverage of the electrolyte surface with SiO 2 seems almost inevitable in the case of model anodes.

[1]  Ellen Ivers-Tiffée,et al.  Correlation between microstructure and degradation in conductivity for cubic Y2O3-doped ZrO2 , 2006 .

[2]  I. Chorkendorff,et al.  Effect of impurities on structural and electrochemical properties of the Ni-YSZ interface. , 2003 .

[3]  Ellen Ivers-Tiffée,et al.  Model anodes and anode models for understanding the mechanism of hydrogen oxidation in solid oxide fuel cells. , 2010, Physical chemistry chemical physics : PCCP.

[4]  H. Brongersma,et al.  The limiting factor for oxygen exchange at the surface of fuel cell electrolytes , 2003 .

[5]  R. Schneider,et al.  Decomposition of 8.5 mol.% Y2O3-doped zirconia and its contribution to the degradation of ionic conductivity , 2009 .

[6]  Mogens Bjerg Mogensen,et al.  Time-of-flight secondary ion mass spectrometry as a tool for studying segregation phenomena at nickel–YSZ interfaces , 2006 .

[7]  L. Gauckler,et al.  Reaction mechanism of Ni pattern anodes for solid oxide fuel cells , 2000 .

[8]  Masamichi Ippommatsu,et al.  Preparation of Nickel Pattern Electrodes on YSZ and Their Electrochemical Properties in  H 2 ‐  H 2 O  Atmospheres , 1994 .

[9]  M. Mogensen,et al.  Three-phase-boundary dynamics at the Ni/ScYSZ interface , 2009 .

[10]  Mogens Bjerg Mogensen,et al.  Effects of trace elements at the Ni/ScYSZ interface in a model solid oxide fuel cell anode , 2008 .

[11]  M. Mogensen,et al.  TOF‐SIMS studies of yttria‐stabilised zirconia , 2006 .

[12]  Hubert A. Gasteiger,et al.  Handbook of fuel cells : fundamentals technology and applications , 2003 .

[13]  J. Winkler,et al.  Geometric Requirements of Solid Electrolyte Cells with a Reference Electrode , 1998 .

[14]  M. Mogensen,et al.  Characterisation of the Ni/ScYSZ interface in a model solid oxide fuel cell anode , 2008 .

[15]  Mogens Bjerg Mogensen,et al.  Microstructural and chemical changes at the Ni/YSZ interface , 2001 .