Friction Damper Optimization: Simulation of Rainbow Tests

Friction dampers have been used to reduce turbine blade vibration levels for a considerable period of time. However, optimal design of these dampers has been quite difficult due both to a lack of adequate theoretical predictions and to difficulties in conducting reliable experiments. One of the difficulties of damper weight optimization via the experimental route has been the inevitable effects of mistuning. Also, conducting separate experiments for different damper weights involves excessive cost. Therefore, current practice in the turbomachinery industry has been to conduct so-called rainbow tests where friction dampers with different weights are placed between blades with a predefined configuration. However, it has been observed that some rainbow test results have been difficult to interpret and have been inconclusive for determining the optimum damper weight for a given bladed-disk assembly. A new method of analysis-a combination of the harmonic balance method and structural modification approaches-is presented in this paper for the analysis of structures with friction interfaces and the method is applied to search for qualitative answers about the so-called rainbow tests in turbomachinery applications. A simple lumped-parameter model of a bladed-disk model was used and different damper weights were modeled using friction elements with different characteristics. Resonance response levels were obtained for bladed disks with various numbers of blades under various engine-order excitations. It was found that rainbow tests, where friction dampers with different weights are used on the same bladed-disk assembly, can be used to find the optimum damper weight if the mode of vibration concerned has weak blade-to-blade coupling (the case where the disk is almost rigid and blades vibrate almost independently from each other). Otherwise, it is very difficult to draw any reliable conclusion from such expensive experiments.

[1]  Alok Sinha,et al.  Probabilistic Method to Compute the Optimal Slip Load for a Mistuned Bladed Disk Assembly With Friction Dampers , 1990 .

[2]  Wilfred D. Iwan,et al.  On a Class of Models for the Yielding Behavior of Continuous and Composite Systems , 1967 .

[3]  D. J. Ewins,et al.  Resonant Vibration Levels of a Mistuned Bladed Disk , 1984 .

[4]  L. E. Goodman,et al.  Energy Dissipation in Contact Friction: Constant Normal and Cyclic Tangential Loading , 1962 .

[5]  David J. Ewins,et al.  Underplatform Dampers for Turbine Blades: Theoretical Modelling, Analysis and Comparison With Experimental Data , 1999 .

[6]  Marc P. Mignolet,et al.  Effects of Damping and Damping Mistuning on the Forced Vibration Response of Bladed Disks , 1993 .

[7]  Walter Sextro,et al.  Improved Reliability of Bladed Disks due to Friction Dampers , 1997 .

[8]  Mehmet Imregun,et al.  Harmonic Balance Vibration Analysis of Turbine Blades With Friction Dampers , 1997 .

[9]  A. Cowley,et al.  An Elastic Mechanism for the Micro-Sliding Characteristics between Contacting Machined Surfaces , 1978 .

[10]  Earl H. Dowell,et al.  Multi-Harmonic Analysis of Dry Friction Damped Systems Using an Incremental Harmonic Balance Method , 1985 .

[11]  G. Boothroyd,et al.  Damping at Metallic Interfaces Subjected to Oscillating Tangential Loads , 1975 .

[12]  Wieslaw Ostachowicz.  The harmonic balance method for determining the vibration parameters in damped dynamic systems , 1989 .

[13]  Pascal Drazetic,et al.  On a direct inversion of the impedance matrix in response reanalysis , 1996 .

[14]  J. Hollkamp,et al.  Effects of damping on a blade-disk assembly , 1997 .

[15]  M. Hajek,et al.  Stick-slip motion of turbine blade dampers , 1992, Philosophical Transactions of the Royal Society of London. Series A: Physical and Engineering Sciences.

[16]  David J. Ewins,et al.  Underplatform Dampers for Turbine Blades: Theoretical Modeling, Analysis, and Comparison With Experimental Data , 2001 .

[17]  J. Griffin,et al.  An Alternating Frequency/Time Domain Method for Calculating the Steady-State Response of Nonlinear Dynamic Systems , 1989 .

[18]  David J. Ewins,et al.  MODELLING TWO-DIMENSIONAL FRICTION CONTACT AND ITS APPLICATION USING HARMONIC BALANCE METHOD , 1996 .

[19]  Ulrich Schaber.  Non-Contact Vibration Measurements of Mistuned Coupled Blades , 1997 .

[20]  William W. Hager,et al.  Updating the Inverse of a Matrix , 1989, SIAM Rev..

[21]  D.I.G. Jones,et al.  On tuned bladed disk dynamics: Some aspects of friction related mistuning , 1983 .

[22]  Chia-Hsiang Menq,et al.  The influence of microslip on vibratory response, part I: A new microslip model , 1986 .

[23]  R. C. F. Dye,et al.  Vibration Amplitudes of Compressor Blades Resulting From Scatter in Blade Natural Frequencies , 1969 .

[24]  Robert E. Kielb,et al.  An Integrated Approach for Friction Damper Design , 1990 .

[25]  C. Pierre,et al.  EFFECTS OF DRY FRICTION DAMPING ON THE OCCURRENCE OF LOCALIZED FORCED VIBRATIONS IN NEARLY CYCLIC STRUCTURES , 1989 .

[26]  Chia-Hsiang Menq,et al.  A Comparison of Transient and Steady State Finite Element Analyses of the Forced Response of a Frictionally Damped Beam , 1985 .