Passive-intermodulation analysis between rough rectangular waveguide flanges

A new model is presented for the calculation of passive intermodulation (PIM) in waveguide connections. The model considers the roughness of interconnecting waveguide surfaces and the presence of an insulator layer (oxide and contaminants) on these metal surfaces. This results in the generation of a contact resistance, which can excite the PIM level. In particular, the case in which metal-insulator-metal regions are the PIM source is especially investigated. The intermodulation level response is calculated for different waveguide junction parameters like applied mechanical load, surface finish, or metal properties showing qualitative agreement with the measured data published by previous authors.

[1]  Farrokh Arazm,et al.  Nonlinearities in Metal Contacts at Microwave Frequencies , 1980, IEEE Transactions on Electromagnetic Compatibility.

[2]  J. Simmons.  Generalized Formula for the Electric Tunnel Effect between Similar Electrodes Separated by a Thin Insulating Film , 1963 .

[3]  R. Cox.  Measurements of Waveguide Component and Joint Mixing Products in 6-GHz Frequency Diversity Systems , 1970 .

[4]  D. Pollard,et al.  Passive intermodulation product generation in high power communications satellites , 1986 .

[5]  D. Bogy,et al.  An Elastic-Plastic Model for the Contact of Rough Surfaces , 1987 .

[6]  J. V. Rootsey,et al.  Intermodulation study. Intermodulation products: Satellite ground antennas , 1973 .

[7]  P. L. Lui,et al.  Passive intermodulation interference in communication systems , 1990 .

[8]  E. Weibel,et al.  Tests evaluate the influence of junctions on PIM , 1998 .

[9]  C. Karagiannopoulos,et al.  Physical interpretations concerning nonlinear conductivity phenomena across no-load switching contacts , 1990, Thirty-Sixth IEEE Conference on Electrical Contacts, and the Fifteenth International Conference on Electrical Contacts.

[10]  H. Grubin.  The physics of semiconductor devices , 1979, IEEE Journal of Quantum Electronics.

[11]  J. Greenwood,et al.  Contact of nominally flat surfaces , 1966, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[12]  D. Landolt,et al.  Thickness of natural oxide films determined by AES and XPS with/without sputtering , 1985 .

[13]  F. A. Benson,et al.  Intermodulation products from nonlinearities in transmission lines and connectors at microwave frequencies , 1975 .

[14]  M. Braunovic,et al.  Thermoelastic ratcheting effect in bolted aluminum-to-aluminum connections , 1988 .

[15]  Izhak Etsion,et al.  A Finite Element Based Elastic-Plastic Model for the Contact of Rough Surfaces , 2003 .

[16]  Z. Hurych,et al.  Influence of non-uniform thickness of dielectric layers on capacitance and tunnel currents , 1966 .

[17]  Izhak Etsion,et al.  Static Friction Coefficient Model for Metallic Rough Surfaces , 1988 .

[18]  C. D. Bond,et al.  Intermodulation generation by electron tunneling through aluminum-oxide films , 1979, Proceedings of the IEEE.

[19]  Giuseppe Pelosi,et al.  Passive intermodulation on large reflector antennas , 2002 .

[20]  J. I. McCool,et al.  Predicting Microfracture in Ceramics Via a Microcontact Model , 1986 .

[21]  J.W. Boyhan,et al.  Satellite passive intermodulation: systems considerations , 1996, IEEE Transactions on Aerospace and Electronic Systems.

[22]  C. Chow.  Effect of Insulating‐Film‐Thickness Nonuniformity on Tunnel Characteristics , 1963 .

[23]  J. Halling,et al.  The normal approach between rough flat surfaces in contact , 1975 .

[24]  J. Horng,et al.  An Elliptic Elastic-Plastic Asperity Microcontact Model for Rough Surfaces , 1998 .

[25]  R. D. Malucci.  Multispot model of contacts based on surface features , 1990, Thirty-Sixth IEEE Conference on Electrical Contacts, and the Fifteenth International Conference on Electrical Contacts.

[26]  P. Dobson.  Physics of Semiconductor Devices (2nd edn) , 1982 .