Low temperature Si/Si wafer direct bonding using a plasma activated method

Manufacturing and integration of micro-electro-mechanical systems (MEMS) devices and integrated circuits (ICs) by wafer bonding often generate problems caused by thermal properties of materials. This paper presents a low temperature wafer direct bonding process assisted by O2 plasma. Silicon wafers were treated with wet chemical cleaning and subsequently activated by O2 plasma in the etch element of a sputtering system. Then, two wafers were brought into contact in the bonder followed by annealing in N2 atmosphere for several hours. An infrared imaging system was used to detect bonding defects and a razor blade test was carried out to determine surface energy. The bonding yield reaches 90%–95% and the achieved surface energy is 1.76 J/m2 when the bonded wafers are annealed at 350 °C in N2 atmosphere for 2 h. Void formation was systematically observed and elimination methods were proposed. The size and density of voids greatly depend on the annealing temperature. Short O2 plasma treatment for 60 s can alleviate void formation and enhance surface energy. A pulling test reveals that the bonding strength is more than 11.0 MPa. This low temperature wafer direct bonding process provides an efficient and reliable method for 3D integration, system on chip, and MEMS packaging.

[1]  T. Suga,et al.  Combined process for wafer direct bonding by means of the surface activation method , 2004, 2004 Proceedings. 54th Electronic Components and Technology Conference (IEEE Cat. No.04CH37546).

[2]  Edward Hæggström,et al.  Fabricating capacitive micromachined ultrasonic transducers with wafer-bonding technology , 2003 .

[3]  A. Plößl.  Wafer direct bonding: tailoring adhesion between brittle materials , 1999 .

[4]  Rajendra Singh,et al.  Wafer Direct Bonding: From Advanced Substrate Engineering to Future Applications in Micro/Nanoelectronics , 2006, Proceedings of the IEEE.

[5]  N. Aitken,et al.  Surface activation for low temperature wafer fusion bonding by radicals produced in an oxygen discharge , 2009 .

[6]  Tadatomo Suga,et al.  Nanoadhesion layer for enhanced Si-Si and Si-SiN wafer bonding , 2012, Microelectron. Reliab..

[7]  Cheng-Ta Ko,et al.  Wafer-level bonding/stacking technology for 3D integration , 2010, Microelectron. Reliab..

[8]  M. Schmidt.  Wafer-to-wafer bonding for microstructure formation , 1998, Proc. IEEE.

[9]  Zhu Huilong.  Wafer Level Bonding Technology for 3-D Integration , 2012 .

[10]  C. Klages,et al.  Atmospheric-pressure plasma pretreatment for direct bonding of silicon wafers at low temperatures , 2008 .

[11]  Q. Wang,et al.  Wafer-level low temperature bonding with Au-In system , 2007, 2007 Proceedings 57th Electronic Components and Technology Conference.

[12]  C. Dunare,et al.  SOI materials for MOEMS obtained by silicon direct bonding technique , 2000, 2000 International Semiconductor Conference. 23rd Edition. CAS 2000 Proceedings (Cat. No.00TH8486).

[13]  Yuxi Yu,et al.  Low Temperature Wafer Direct Bonding Using Wet Chemical Treatment , 2012 .

[14]  M. Schmidt,et al.  Wafer-Level Thermocompression Bonds , 2003 .

[15]  T. Suga,et al.  Room Temperature Si/Si Wafer Direct Bonding in Air , 2007, 2007 8th International Conference on Electronic Packaging Technology.

[16]  T. Suga,et al.  Room temperature wafer bonding using surface activated bonding method , 2008, 2008 IEEE 9th VLSI Packaging Workshop of Japan.

[17]  J. Raskin,et al.  Low-temperature wafer bonding: a study of void formation and influence on bonding strength , 2005, Journal of Microelectromechanical Systems.

[18]  M. Schmidt,et al.  Characterization of wafer-level thermocompression bonds , 2004, Journal of Microelectromechanical Systems.

[19]  Hung-Yi Lin,et al.  Effect of surface treatment on wafer direct bonding process , 2004 .

[20]  N. Rolland,et al.  A novel packaging method using wafer-level BCB polymer bonding and glass wet-etching for RF applications , 2008 .

[21]  U. Gösele,et al.  Semiconductor wafer bonding , 1998 .

[22]  K. Hjort,et al.  Evaluation of InP-to-silicon heterobonding , 2001 .

[23]  Matiar M. R. Howlader,et al.  Void-free strong bonding of surface activated silicon wafers from room temperature to annealing at 600 °C , 2010 .