Analysis of weld characteristics of micro-plasma arc welding and tungsten inert gas welding of thin stainless steel (304L) sheet

This research work focuses on comparison of the weld geometry, distortion, microstructure and mechanical properties of thin SS 304 L sheets (0.8 mm thickness) welded using micro-plasma arc welding and tungsten inert gas welding process. Initial experiments were performed to identify suitable processing parameters for micro-plasma arc welding and tungsten inert gas welding processes. Microstructures of welds were analysed using scanning electron microscopy, X-ray diffraction and energy dispersive spectroscopy. The results indicate that the joint produced by micro-plasma arc welding exhibited higher tensile strength, higher ductility, smaller dendrite size and a narrow heat affected zone. Samples welded by micro-plasma arc welding process had lower distortion as compared to that welded by tungsten inert gas process. Micro-plasma arc welding was shown to be the suitable process for welding of thin 304 L sheets owing to its higher welding speed and better weld properties as compared to the tungsten inert gas welding process.

[1]  WU C.S.,et al.  Sensing Dynamic Keyhole Behaviors in Controlled-Pulse Keyholing Plasma Arc Welding , 2013 .

[2]  C. Wu,et al.  Experimental sensing of the keyhole exit deviation from the torch axis in plasma arc welding , 2014 .

[3]  Her-Yueh Huang,et al.  Research on the activating flux gas tungsten arc welding and plasma arc welding for stainless steel , 2010 .

[4]  Michela Simoncini,et al.  Effect of the welding parameters and tool configuration on micro- and macro-mechanical properties of similar and dissimilar FSWed joints in AA5754 and AZ31 thin sheets , 2012 .

[5]  A. Durgutlu.  Experimental investigation of the effect of hydrogen in argon as a shielding gas on TIG welding of austenitic stainless steel , 2004 .

[6]  Abbas Ebnonnasir,et al.  Artificial neural network modeling for evaluating of epitaxial growth of Ti6Al4V weldment , 2006 .

[7]  Satya Prakash,et al.  Investigation on AISI 304 austenitic stainless steel to AISI 4140 low alloy steel dissimilar joints by gas tungsten arc, electron beam and friction welding , 2011 .

[8]  Godwin Kwame Ahiale,et al.  Microstructure and fatigue resistance of high strength dual phase steel welded with gas metal arc welding and plasma arc welding processes , 2013, Metals and Materials International.

[9]  Jianxun Zhang,et al.  A comparative study of pulsed Nd:YAG laser welding and TIG welding of thin Ti6Al4V titanium alloy plate , 2013 .

[10]  Weite Wu,et al.  Effect of vibration on microstructures and mechanical properties of 304 stainless steel GTA welds , 2013, Metals and Materials International.

[11]  K. Tseng,et al.  Performance of activated TIG process in austenitic stainless steel welds , 2011 .

[12]  Y. Morisada,et al.  Development of simplified active flux tungsten inert gas welding for deep penetration , 2014 .

[13]  Xiaoyan Zeng,et al.  Study on microstructure and mechanical properties of 304 stainless steel joints by TIG, laser and laser-TIG hybrid welding , 2010 .

[14]  M. T. Montañés,et al.  Effect of different micro-plasma arc welding (MPAW) processes on the corrosion of AISI 316L SS tubes in LiBr and H3PO4 solutions under flowing conditions , 2010 .

[15]  YuMing Zhang,et al.  Bilinear Model Predictive Control of Plasma Keyhole Pipe Welding Process , 2014 .

[16]  Y. M. Zhang,et al.  Control of dynamic keyhole welding process , 2007, Autom..

[17]  M. T. Montañés,et al.  Effect of the micro-plasma arc welding technique on the microstructure and pitting corrosion of AISI 316L stainless steels in heavy LiBr brines , 2011 .

[18]  D. Lin,et al.  Precipitation examination of δ, σ, and γ phases using modified Cr/Ni equivalent ratios during the multipass welding of stainless steels , 2009 .

[19]  Yuming Zhang,et al.  Predictive Control for Manual Plasma Arc Pipe Welding , 2014 .

[20]  J. García-Antón,et al.  Effects of microplasma arc AISI 316L welds on the corrosion behaviour of pipelines in LiBr cooling systems , 2013 .

[21]  John C. Lippold,et al.  Welding Metallurgy and Weldability of Stainless Steels , 2005 .

[22]  Chuansong Wu,et al.  Plasma arc welding: Process, sensing, control and modeling , 2014 .

[23]  G. Lothongkum,et al.  TIG pulse welding of 304L austenitic stainless steel in flat, vertical and overhead positions , 1999 .

[24]  Yiyi Li,et al.  Study of the law between the weld pool shape variations with the welding parameters under two TIG processes , 2012 .

[25]  Subodh Kumar,et al.  Effect of heat input on the microstructure and mechanical properties of gas tungsten arc welded AISI 304 stainless steel joints , 2011 .

[26]  M. Atapour,et al.  Microstructure and corrosion behavior of multipass gas tungsten arc welded 304L stainless steel , 2014 .

[27]  Renu Gupta,et al.  Key- Hole Plasma Arc Welding Of 8 Mm Thick Maraging Steel — A Comparison With Multi- Pass Gtaw , 2012, Welding in the World.