Workspace Determination and Feedback Control of a Pick-and-Place Parallel Robot: Analysis and Experiments

The authors report on the analysis and experimental evaluation of a parallel Schönflies-motion generator (SMG) intended for fast pick-and-place operations and actuated with cylindrical drives (C-drives). Its CRRHHRRC isostatic architecture offers high rotability of the moving platform and a reduced number of limbs, as compared to robots available on the market. A simulation model using the dynamics of the robot as well as an experimental prototype are described. The results obtained are used to assess the pros and cons of two alternative C-drive architectures. A workspace analysis including the feasible wrenches is conducted. The industry standard Adept test cycle is used to evaluate the performance of the prototype. The data obtained prove that C-drives augmented with strain-wave gears give the SMG significantly better wrench capabilities and lower trajectory-tracking error, compared to their alternative C-drives based on cables.

[1]  Po-Chih Lee,et al.  Singularity and workspace analysis of three isoconstrained parallel manipulators with schoenflies motion , 2012 .

[2]  Daniel Martins,et al.  Wrench capability in redundant planar parallel manipulators with net degree of constraint equal to four, five or six , 2016 .

[3]  Reymond Clavel,et al.  Kinematic calibration of the parallel Delta robot , 1998, Robotica.

[4]  J. Angeles,et al.  Optimization of a Test Trajectory for SCARA Systems , 2008 .

[5]  Sébastien Krut,et al.  Par4: very high speed parallel robot for pick-and-place , 2005, 2005 IEEE/RSJ International Conference on Intelligent Robots and Systems.

[6]  Marcello Pellicciari,et al.  A method for reducing the energy consumption of pick-and-place industrial robots , 2013 .

[7]  Clément Gosselin,et al.  Kinematic-Sensitivity Indices for Dimensionally Nonhomogeneous Jacobian Matrices , 2010, IEEE Transactions on Robotics.

[8]  O Company,et al.  Simplified dynamic modelling and improvement of a four-degree-of-freedom pick-and-place manipulator with articulated moving platform , 2009 .

[9]  Sébastien Briot,et al.  Pantopteron-4: A new 3T1R decoupled parallel manipulator for pick-and-place applications , 2010 .

[10]  Chung-Ching Lee,et al.  Type synthesis of primitive Schoenflies-motion generators , 2009 .

[11]  Farrokh Janabi-Sharifi,et al.  Cooperative Continuum Robots: Concept, Modeling, and Workspace Analysis , 2018, IEEE Robotics and Automation Letters.

[12]  Jorge Angeles,et al.  The translating Π-joint: Design and applications , 2018 .

[13]  D. Caleb Rucker,et al.  Analysis and Validation of a Teleoperated Surgical Parallel Continuum Manipulator , 2016, IEEE Robotics and Automation Letters.

[14]  Alessandro Gasparetto,et al.  Validation of Minimum Time-Jerk Algorithms for Trajectory Planning of Industrial Robots , 2011 .

[15]  Scott B. Nokleby,et al.  Wrench capabilities of planar parallel manipulators. Part I: Wrench polytopes and performance indices , 2008, Robotica.

[16]  J. Angeles,et al.  The Formulation of Dynamical Equations of Holonomic Mechanical Systems Using a Natural Orthogonal Complement , 1988 .

[17]  Jorge Angeles,et al.  Trajectory-Planning and Normalized-Variable Control for Parallel Pick-and-Place Robots , 2019, Journal of Mechanisms and Robotics.

[18]  J. Angeles,et al.  An innovative tooth root profile for spur gears and its effect on service life , 2017 .

[19]  J. Merlet.  Jacobian, Manipulability, Condition Number and Accuracy of Parallel Robots , 2005, ISRR.

[20]  Clément Gosselin,et al.  Workspace and Sensitivity Analysis of a Novel Nonredundant Parallel SCARA Robot Featuring Infinite Tool Rotation , 2016, IEEE Robotics and Automation Letters.

[21]  Jorge Angeles,et al.  The virtual screw: Concept, design and applications , 2018 .

[22]  Hiroshi Makino,et al.  Research and Commercialization of SCARA Robot -The Case of Industry-University Joint Research and Development- , 2007, Int. J. Autom. Technol..

[23]  Toru Omata,et al.  Four-Degree-of-Freedom Parallel Mechanism Mobile Robots , 2008 .

[24]  Jorge Angeles,et al.  The development of an innovative two-DOF cylindrical drive: Design, analysis and preliminary tests , 2014, 2014 IEEE International Conference on Robotics and Automation (ICRA).

[25]  Tsuneo Yoshikawa,et al.  Manipulability of Robotic Mechanisms , 1985 .

[26]  Jorge Angeles,et al.  The dynamics of a parallel Schönflies-motion generator , 2018 .

[27]  J. M. Hervé.  The Lie group of rigid body displacements, a fundamental tool for mechanism design , 1999 .