MEMS-based components of a miniature fuel cell/fuel reformer system

Abstract The components of a novel miniature fuel cell/fuel reformer system fueled by liquid gases such as butane and propane were prototyped by MEMS technology and tested. In this system, fuel, air and water are supplied to the fuel reformer by utilizing the vapor pressure of the liquid gas for the reduction of power consumption by peripherals and the simplification of the system. The system is composed of a reforming reactor, a catalytic combustor, a polymer electrolyte fuel cell (PEFC), an ejector to supply air to the combustor and other peripherals. The reforming reactor demonstrated the steam reforming of methanol at an equivalent power of 200 mW and a total efficiency of 6%. The combustor had a stable combustion area above 5 W, and the complete combustion of butane was confirmed by gas chromatography. The ejector showed a potential to supply air required for the complete combustion of butane (31 times larger volume than butane). The PEFC worked, but only at low power density of about 0.1 mW/cm2 due to poor adhesion between a polymer electrolyte membrane (PEM) and catalytic electrodes.

[1]  K. Jensen,et al.  Combustion-assisted hydrogen production in a high-temperature chemical reactor/heat exchanger for portable fuel cell applications , 2003, TRANSDUCERS '03. 12th International Conference on Solid-State Sensors, Actuators and Microsystems. Digest of Technical Papers (Cat. No.03TH8664).

[2]  Chunbo Zhang,et al.  Micro combustion-thermionic power generation: feasibility, design and initial results , 2003, TRANSDUCERS '03. 12th International Conference on Solid-State Sensors, Actuators and Microsystems. Digest of Technical Papers (Cat. No.03TH8664).

[3]  M. Esashi,et al.  Silicon-based micro-polymer electrolyte fuel cells , 2003, The Sixteenth Annual International Conference on Micro Electro Mechanical Systems, 2003. MEMS-03 Kyoto. IEEE.

[4]  Khalil Najafi,et al.  An Integrated Combustor-Thermoelectric Micro Power Generator , 2001 .

[5]  M. Esashi,et al.  Combustor-integrated micro-fuel processor with suspended membrane structure , 2003, TRANSDUCERS '03. 12th International Conference on Solid-State Sensors, Actuators and Microsystems. Digest of Technical Papers (Cat. No.03TH8664).

[6]  M. Esashi,et al.  MEMS-Based Polymer Electrolyte Fuel Cell , 2002 .

[7]  K. Jensen,et al.  A thermophotovoltaic micro-generator for portable power applications , 2003, TRANSDUCERS '03. 12th International Conference on Solid-State Sensors, Actuators and Microsystems. Digest of Technical Papers (Cat. No.03TH8664).

[8]  K. Jensen,et al.  A Combustion-Based MEMS Thermoelectric Power Generator , 2001 .

[9]  S. Tanaka.  Design and Fabrication Challenges for Micromachined Gas Turbine Generators , 2002 .

[10]  Evan O. Jones,et al.  Microfuel processor for use in a miniature power supply , 2002 .

[11]  Masayoshi Esashi,et al.  Development of Micro-Turbo Charger and Micro-Combustor as Feasibility Studies of Three-Dimensional Gas Turbine at Micro-Scale , 2003 .

[12]  Y. Kubo,et al.  Small Direct Methanol Fuel Cell Pack for Portable Applications , 2002 .

[13]  Christopher Hebling,et al.  Fuel Cells for Low Power Applications , 2002 .

[14]  Suk Won Cha,et al.  Design and fabrication of a micro fuel cell array with “flip-flop” interconnection , 2002 .

[15]  Alan F. Jankowski,et al.  Novel proton exchange membrane thin-film fuel cell for microscale energy conversion , 2000 .

[16]  Alan H. Epstein,et al.  Millimeter-Scale, MEMS Gas Turbine Engines , 2003 .