Dynamic testing and modelling of composite fuselage frames and fasteners for aircraft crash simulations

In crash simulations of composite aircraft fuselage sections, frame breaking, skin bending and failure of mechanically fastened joints can typically be identified as major contributors to crash energy absorption. In order to generate a database for model validations, corresponding static and dynamic tests have been performed on coupon and structural element level to characterise the rate-dependent failure behaviour and energy absorption. Skin-bending, frame-bending and joint-failure tests under pull-out, bearing and peeling loads were performed on 977-2/HTS carbon fibre/epoxy specimens. On the one hand, effects of loading rate on the frame-bending behaviour could be observed. On the other hand, fastener failure did not appear to be depending on loading rate for the test speeds up to 10 m/s involved in this study. Adequate modelling methods in Abaqus/Explicit were derived and validated, and finally applied to a global aircraft crash simulation model.

[1]  Don Kelly,et al.  A study of fastener pull-through failure of composite laminates. Part 2: Failure prediction , 1999 .

[2]  Matthias Waimer,et al.  The Kinematics Model - A Numerical Method for the Development of a Crashworthy Composite Fuselage Design of Transport Aircraft , 2010 .

[3]  Guy Gendron,et al.  Stress and failure analysis of mechanically fastened joints in composite laminates , 2000 .

[4]  Tomas Ireman,et al.  On damage development in mechanically fastened composite laminates , 2000 .

[5]  Richard L. Boitnott,et al.  An analytical and experimental investigation of the response of the curved, composite frame/skin specimens , 1994 .

[6]  Norman Jones,et al.  Influence of spot-weld failure on crushing of thin-walled structural sections , 2003 .

[7]  Lorenzo Iannucci,et al.  Pull-through performance of carbon fibre epoxy composites , 2012 .

[8]  Hao Peng,et al.  Research Development of Crashworthiness Simulation Evaluation on Civil Aircraft , 2011 .

[9]  Bertrand Langrand,et al.  Détermination expérimentale du comportement mécanique et de critère de rupture d'assemblages sous chargements mixtes. Application aux rivets et points soudés , 2003 .

[10]  Conor T. McCarthy,et al.  An analytical model for the prediction of through-thickness stiffness in tension-loaded composite bolted joints , 2012 .

[11]  R. L. Sierakowski,et al.  Strain Rate Effects in Composites , 1997 .

[12]  Kazuo Iwasaki,et al.  Summary of Vertical Drop Tests of YS-11 Transport Fuselage Sections , 2003 .

[13]  Tong V. Vu,et al.  Vertical Drop Test of a Narrow-Body Fuselage Section with Overhead Stowage Bins and Auxiliary Fuel Tank System on Board. , 1995 .

[14]  Don Kelly,et al.  A study of fastener pull-through failure of composite laminates. Part 1: Experimental , 1999 .

[15]  R. S. Birch,et al.  Static and dynamic behaviour of composite riveted joints in tension , 2001 .

[16]  Ali Fatemi,et al.  An experimental investigation of deformation and fatigue behavior of coach peel riveted joints , 2006 .

[17]  Alastair Johnson,et al.  Numerical Investigation of Dynamically Loaded Bolted Joints in Carbon Fibre Composite Structures , 2010 .

[18]  Ch. Kindervater,et al.  Composite vehicle structural crashworthiness - A status of design methodology and numerical simulation techniques , 1999 .

[19]  Rodney S. Thomson,et al.  Experimental Investigation of Dynamically Loaded Bolted Joints in Carbon Fibre Composite Structures , 2010 .

[20]  Conor T. McCarthy,et al.  An analytical model for the prediction of load distribution in highly torqued multi-bolt composite joints , 2011 .

[21]  F. Beltran,et al.  Finite element methodologies development to simulate the behaviour of composite fuselage structure and correlation with drop test , 2001 .

[22]  Peter Middendorf,et al.  Strain rate effects in phenolic composites and phenolic-impregnated honeycomb structures , 2007 .

[23]  K. H. Lyle,et al.  A History of Full-Scale Aircraft and Rotorcraft Crash Testing and Simulation at NASA Langley Research Center , 2004 .

[24]  A. Beevers,et al.  Analysis of stiffness of adhesive joints in car bodies , 2001 .

[25]  S. Heimbsa,et al.  Numerical simulation of aircraft interior components under crash loads , 2008 .

[26]  Pedro P. Camanho,et al.  Stress analysis and strength prediction of mechanically fastened joints in FRP: A review , 1997 .

[27]  Srinivasa D. Thoppul,et al.  Mechanics of mechanically fastened joints in polymer–matrix composite structures – A review , 2009 .

[28]  Raphael T. Haftka,et al.  Optimal Design of Composite Fuselage Frames for Crashworthiness , 1996 .

[29]  Sebastian Heimbs,et al.  Static and dynamic failure behaviour of bolted joints in carbon fibre composites , 2013 .

[30]  R. S. Thomson,et al.  Fastener pull-through in a carbon fibre epoxy composite joint , 2008 .

[31]  David J. Elder,et al.  DEVELOPMENT OF FASTENER MODELS FOR IMPACT SIMULATION OF COMPOSITE STRUCTURES , 2006 .

[32]  Masakatsu Minegishi,et al.  Vertical Drop Test of a Transport Fuselage Section , 2002 .

[33]  S M R Hashemi,et al.  A systematic approach to aircraft crashworthiness and impact surface material models , 2000 .

[34]  G. S. Ger,et al.  DYNAMIC TENSILE STRENGTH OF COMPOSITE LAMINATE JOINTS FASTENED MECHANICALLY , 1996 .

[35]  Rodney S. Thomson,et al.  Experimental investigation of damage progression and strength of countersunk composite joints , 2012 .

[36]  M M Sadeghi,et al.  Modelling Verification of an Airframe Section and Comparisons With Impact Test , 1996 .

[37]  Joakim Schön,et al.  Quasi-static behaviour of composite joints with protruding-head bolts , 2001 .

[38]  Rodney S. Thomson,et al.  Numerical analysis of damage progression and strength of countersunk composite joints , 2012 .

[39]  Alastair Johnson,et al.  Experimental and Numerical Analysis of Composite Folded Sandwich Core Structures Under Compression , 2007 .

[40]  L Fasanella Edwin,et al.  Crash Simulation of a Vertical Drop Test of a B737 Fuselage Section With Overhead Bins and Luggage , 2001 .

[41]  G. N. Labeas,et al.  Strength prediction of bolted joints in graphite/epoxy composite laminates , 2002 .

[42]  Hamid M. Lankarani,et al.  A modern aerospace modeling approach for evaluation of aircraft fuselage crashworthiness , 2003 .