Exploring novel high power density concepts for attractive fusion systems

Abstract The Advanced Power Extraction (APEX) study is aimed at exploring innovative concepts for fusion power technology (FPT) that can tremendously enhance the potential of fusion as an attractive and competitive energy source. Specifically, the study is exploring new and ‘revolutionary’ concepts that can provide the capability to efficiently extract heat from systems with high neutron and surface heat loads while satisfying all the FPT functional requirements and maximizing reliability, maintainability, safety, and environmental attractiveness. The primary criteria for measuring performance of the new concepts are: (1) high power density capability with a peak neutron wall load (NWL) of ∼10 MW m −2 and surface heat flux of ∼2 MW m −2 ; (2) high power conversion efficiency, ∼40% net; and (3) clear potential to achieve high availability; specifically low failure rate, large design margin, and short downtime for maintenance. A requirement that MTBF>43 MTTR was derived as a necessary condition to achieve the required first wall/blanket availability, where MTBF is the mean time between failures and MTTR is the mean time to recover. Highlights of innovative and promising new concepts that may satisfy these criteria are provided.

[1]  Mohamed A. Abdou,et al.  Application of reliability analysis method to fusion component testing , 1995 .

[2]  Ralph W. Moir,et al.  Rotating liquid blanket for a toroidal fusion reactor , 1987 .

[3]  N. M. Ghoniem,et al.  Viscoelastic analysis of mismatch stresses in ceramic matrix composites under high-temperature neutron irradiation☆ , 1995 .

[4]  W. R. Meier,et al.  Reactor concepts for laser fusion , 1977 .

[5]  Dai-Kai Sze,et al.  Technical issues and requirements of experiments and facilities for fusion nuclear technology , 1985 .

[6]  Ralph W. Moir,et al.  HYLIFE-II Inertial Confinement Fusion Reactor Design , 1991 .

[7]  Steven J. Zinkle,et al.  Defect production in ceramics , 1997 .

[8]  R. W. Moir,et al.  Liquid first walls for magnetic fusion energy configurations , 1997 .

[9]  J. Holdren,et al.  Safety and Environmental Aspects of Fusion Energy , 1991 .

[10]  Ronald L. Miller,et al.  Fusion Power Plant Economics , 1996 .

[11]  N. C. Christofilos,et al.  Design for a high power-density Astron reactor , 1989 .

[12]  P. J. Knight,et al.  Key Issues for the Economic Viability of Magnetic Fusion Power , 1996 .

[13]  J. Raeder,et al.  Safety and Environmental Assessment of Fusion Power (SEAFP) , 1995 .

[14]  R.W. Moir.  Mirror-reactor studies , 1981, Proceedings of the IEEE.

[15]  Mark S. Tillack,et al.  Overview of the ARIES-RS reversed-shear tokamak power plant study , 1997 .

[16]  Anton Möslang,et al.  Development of self-cooled liquid metal breeder blankets , 1995 .

[17]  J. Hovingh,et al.  High-Yield Lithium-Injection Fusion-Energy (HYLIFE) reactor , 1985 .

[18]  H. Takatsu,et al.  Development of ceramic breeder blankets in Japan , 1998 .

[19]  Ronald L. Miller.  Economic goals and requirements for competitive fusion energy , 1998 .

[20]  E. Cheng,et al.  A helium-cooled blanket design of the low aspect ratio reactor , 1998 .

[21]  Wayne R. Meier,et al.  Electric power from laser fusion: The HYLIFE concept , 1978 .

[22]  Alice Ying,et al.  Results of an International Study on a High-Volume Plasma-Based Neutron Source for Fusion Blanket Development , 1996 .

[23]  S. Malang,et al.  Limitations on blanket performance , 1999 .

[24]  Neil B. Morley,et al.  X–Ray Surface and Volumetric Heat Deposition and Tritium Breeding Issues in Liquid-Protected FW in High Power Density Devices , 1998 .

[25]  R. Bünde,et al.  Reliability of welds and brazed joints in blankets and its influence on availability , 1991 .

[26]  Mohamed A. Abdou,et al.  A volumetric neutron source for fusion nuclear technology testing and development , 1995 .

[27]  Harold Mindlin,et al.  Aerospace structural metals handbook , 1995 .

[28]  Ulrich Fischer,et al.  European helium cooled pebble bed blanket: Design of blanket: module to be tested in ITER , 1998 .

[29]  M. A. Fütterer,et al.  Development of the EU water-cooled Pb-17Li blanket , 1998 .