Low current arc modes of short length and time: a review

Until the middle of the 20th century the electric arc was known solely as a steady, self sustaining gas discharge phenomenon requiring certain minimum values of current and voltage, depending on the electrode material and the gas environment. Special investigations on material transfer in contacts switching low direct currents, however, revealed step by step that there were certain till then unknown unstable arc modes appearing in extremely short electrode gaps only but requiring minimum current and voltage values distinctly lower than those of the classical steady arc discharge in air. Low current break arcs have to pass one or more of these transient modes whether or not they may eventually attain the steady gas arc mode.

[1]  T. Utsumi,et al.  Fluctuation of Arc Potential Caused by Metal‐Vapor Diffusion in Arcs in Air , 1971 .

[2]  K. Sawa,et al.  Effect of arc behavior on material transfer: a review , 1996, Electrical Contacts - 1996. Proceedings of the Forty-Second IEEE Holm Conference on Electrical Contacts. Joint with the 18th International Conference on Electrical Contacts.

[3]  K. Suhara.  Analysis of metallic phase arc duration at a break contact with the use of Weibull distribution method , 1997, Electrical Contacts - 1997 Proceedings of the Forty-Third IEEE Holm Conference on Electrical Contacts.

[4]  J. P. Treguier,et al.  Electric and Spectroscopic Characterization of Arcing in Electrical Contacts: A Study of Erosion , 1977 .

[5]  F. L. Jones,et al.  Measurement of metal transfer in electrical contacts by the radioactive isotope method , 1961 .

[6]  A. L. Allen.  Long-life contacts for unidirectional currents of 1–20 amperes , 1953 .

[7]  L. Germer,et al.  Physical Processes in Contact Erosion , 1958 .

[8]  I. Dietrich.  Untersuchungen zum kurzen Abreißbogen an schwach belasteten elektrischen Kontakten , 1959 .

[9]  Mitsunori Sato,et al.  Influence of Oxides on Material Transfer Behavior of Silver Base Contacts Containing Various Metal Oxides , 1974 .

[10]  K. Sawa,et al.  Contact resistance characteristics of Ag material in breaking low-load DC arcs , 1994 .

[11]  J. McBride,et al.  The erosion and arc characteristics of Ag/CdO and Ag/SnO/sub 2/ contact materials under DC break conditions , 1996 .

[12]  P. Davidson.  The growth of the liquid bridge in an electrical contact , 1954 .

[13]  M. Hasegawa,et al.  Material transfer characteristic of silver contacts under resistive DC load conditions , 1993, Proceedings of IEEE Holm Conference on Electrical Contacts.

[14]  E. Gray.  Voltage fluctuations in low‐current atmospheric arcs , 1972 .

[15]  L. Germer,et al.  Two Distinct Types of Short Arcs , 1956 .

[16]  N. Ben Jemaa,et al.  Some investigations on slow and fast arc voltage fluctuations for contact materials proceeding in various gases and direct current , 1990 .

[17]  K. Liegmann.  A Unified Explanation of Phenomena in Short Metal-Vapour Arcs in Air , 1978, IEEE Transactions on Plasma Science.

[18]  Koichiro Sawa,et al.  An Experimental Study on Material Transfer and Arc Erosion Characteristic of Ag Contacts under Switching Lower Current (Special Issue on Recent Electromechanical Devices) , 1994 .

[19]  G. Mills,et al.  The Mechanisms of the Showering Arc , 1969 .

[20]  J Riddlestone,et al.  Short duration discharges between separating contacts in a 6 V circuit , 1957 .

[21]  E. Gray,et al.  Stability of low‐current break arcs between palladium contacts , 1973 .

[22]  T. Takagi,et al.  Relationship between Bridge Energy and Metallic Phase Arc Duration in Electric Contacts , 1987 .

[23]  Eoin W. Gray,et al.  Some Spectroscopic Observations of the Two Regions (Metallic Vapor and Gaseous) in Break Arcs , 1973 .

[24]  Koichiro Sawa,et al.  Contact erosion patterns of Pd material in DC breaking arcs , 1993 .

[25]  Tasuku Takagi,et al.  Distribution of Arc Duration and Material Wear Due to Arc for Ag, Cu, and Pd Contacts , 1979 .