Heat transfer improvement due to the imposition of non-uniform wall heating for in-tube laminar forced convection

Abstract This paper explores the bearing that a non-uniform distribution of heat flux used as a wall boundary condition exerts on the heat transfer improvement in a round pipe. Because the overall heat load is considered fixed, the heat transfer improvement is viewed through a reduction in the maximum temperature (‘hot spot’) by imposing optimal distribution of heat flux. Two cases are studied in detail 1) fully developed and 2) developing flow. Peak temperatures in the heated pipe wall are calculated via an analytical approach for the fully developed case, while a numerical simulation based on CFD is employed for the developing case. By relaxing the heat flux distribution on the pipe wall, the numerical results imply that the optimum distribution of heat flux, which minimizes the peak temperatures corresponds with the ‘descending’ distribution. Given that the foregoing approach is quite different from the ‘ascending’ heat flux distribution recommended in the literature by means of the entropy generation minimization (EGM) method, it is inferred that the optimization of heat transfer and fluid flow, in comparison with the thermodynamic optimization, may bring forth quite different guidelines for the designs of thermal systems under the same constraints and circumstances.

[1]  T. M. Hallman,et al.  Steady laminar heat transfer in a circular tube with prescribed wall heat flux , 1958 .

[2]  M. R. Hajmohammadi,et al.  Fork-shaped highly conductive pathways for maximum cooling in a heat generating piece , 2013 .

[3]  Jiangfeng Guo,et al.  Optimization design of heat exchanger in an irreversible regenerative Brayton cycle system , 2013 .

[4]  A. Bejan.  A Study of Entropy Generation in Fundamental Convective Heat Transfer , 1979 .

[5]  Simone Moretti,et al.  Fin Shape Thermal Optimization Using Bejan's Constructal Theory , 2011, Fin Shape Thermal Optimization Using Bejan's Constructal Theory.

[6]  Adrian Bejan,et al.  Design with constructal theory , 2008 .

[7]  A. Bejan,et al.  Constructal law and the unifying principle of design , 2013 .

[8]  Chakravarthy Balaji,et al.  Optimal configuration of discrete heat sources in a vertical duct under conjugate mixed convection using artificial neural networks , 2009 .

[9]  Y. Fautrelle,et al.  Constructal multi-scale structure for maximal heat transfer density , 2003 .

[10]  Javad Abolfazli Esfahani,et al.  Effect of non-uniform heating on entropy generation for the laminar developing pipe flow of a high Prandtl number fluid , 2010 .

[11]  Sadegh Poozesh,et al.  Valuable reconsideration in the constructal design of cavities , 2013 .

[12]  A. Bejan,et al.  The optimal spacing of parallel plates cooled by forced convection , 1992 .

[13]  E. Bilgen,et al.  Natural convection in an open square cavity with discrete heaters at their optimized positions , 2008 .

[14]  XinGang Liang,et al.  Entransy—A physical quantity describing heat transfer ability , 2007 .

[15]  Mingtian Xu,et al.  The Application of Entransy Dissipation Theory in Optimization Design of Heat Exchanger , 2012 .

[16]  Sadegh Poozesh,et al.  Optimal discrete distribution of heat flux elements for in-tube laminar forced convection , 2013 .

[17]  A. Bejan,et al.  Constructal law of design and evolution: Physics, biology, technology, and society , 2013 .

[18]  Sadegh Poozesh,et al.  Radiation Effect on Constructal Design Analysis of a T-Y-Shaped Assembly of Fins , 2012 .

[19]  A. Bejan.  Convection Heat Transfer , 1984 .

[20]  Lingen Chen,et al.  T-shaped assembly of fins with constructal entransy dissipation rate minimization , 2012 .

[21]  L. Tam,et al.  Contribution Analysis of Dimensionless Variables for Laminar and Turbulent Flow Convection Heat Transfer in a Horizontal Tube Using Artificial Neural Network , 2008 .

[22]  Sadegh Poozesh,et al.  Constructal design of multiple heat sources in a square-shaped fin , 2012 .

[23]  A. Bejan.  Entropy Generation Minimization: The Method of Thermodynamic Optimization of Finite-Size Systems and Finite-Time Processes , 1995 .

[24]  G. P. Peterson,et al.  Comparison and optimization of single-phase liquid cooling devices for the heat dissipation of high-power LED arrays , 2013 .

[25]  Sun Feng-rui,et al.  Constructal optimization for H-shaped multi-scale heat exchanger based on entransy theory , 2013 .

[26]  Sadegh Poozesh,et al.  Optimal architecture of heat generating pieces in a fin , 2013 .

[27]  Sadegh Poozesh,et al.  Investigations on the internal shape of Constructal cavities intruding a heat generating body , 2012 .

[28]  Chakravarthy Balaji,et al.  Optimization of the location of multiple discrete heat sources in a ventilated cavity using artificial neural networks and micro genetic algorithm , 2008 .

[29]  Adrian Bejan,et al.  Optimal distribution of discrete heat sources on a plate with laminar forced convection , 2004 .

[30]  M. R. Hajmohammadi,et al.  Improvement of Forced Convection Cooling Due to the Attachment of Heat Sources to a Conducting Thick Plate , 2013 .

[31]  Fengrui Sun,et al.  “Volume-Point” Mass Transfer Constructal Optimization Based on Triangular Element , 2013 .

[32]  Christian J.L. Hermes,et al.  Thermal-hydraulic design of fan-supplied tube-fin condensers for refrigeration cassettes aimed at minimum entropy generation , 2012 .

[33]  A. Bejan,et al.  Entropy Generation Through Heat and Fluid Flow , 1983 .

[34]  Adrian Bejan,et al.  Optimal distribution of discrete heat sources on a wall with natural convection , 2004 .

[35]  Fengrui Sun,et al.  Constructal entransy dissipation rate minimization of a disc , 2011 .

[36]  Chen Lingen.  Progress in study on constructal theory and its applications , 2012 .

[37]  Mohammad Reza Salimpour,et al.  Constructal placement of unequal heat sources on a plate cooled by laminar forced convection , 2012 .