Energy recovery from pyrolysis of plastic waste: Study on non-recycled plastics (NRP) data as the real measure of plastic waste

Abstract Oil produced from pyrolysis of plastics have been known for its higher calorific value than wood-based oil, in which comparable to conventional diesel. Even though many studies have been conducted on pyrolysis of plastics, the findings of those studies are not applied and reported yet according to the real portion of plastic waste. The real amount of plastic waste available is mainly derived from non-recycled plastics (NRP). NRP is defined as the plastic waste that remain in the recycling centers, which unable to be processed due to the certain restrictions. The amounts of NRP vary for each country based on daily applications. In this study, data of NRP in Malaysia, US, UK, as well as global were used to investigate the potential production of liquid fuel based on their different composition of plastic waste. Pyrolysis was conducted in a fixed bed reactor at 500 °C with nitrogen flow of 200 ml/min for 30 min reaction time. The addition of polystyrene (PS) into the NRP composition was also studied to evaluate the improvement of the liquid quality. Several important findings were discussed in this paper including some technical problems, features of the liquid product, characteristics of the by-products and potential energy recovery from NRP. The liquid product was analyzed by various methods such as FTIR, GCMS, elemental analysis and water content.

[1]  T. A. Milne,et al.  Biomass Gasifier "Tars": Their Nature, Formation, and Conversion , 1998 .

[2]  J. N. Sahu,et al.  Pyrolysis of mixtures of palm shell and polystyrene: An optional method to produce a high‐grade of pyrolysis oil , 2014 .

[3]  Nickolas J. Themelis,et al.  2014 ENERGY AND ECONOMIC VALUE OF MUNICIPAL SOLID WASTE (MSW), INCLUDING NON-RECYCLED PLASTICS (NRP), CURRENTLY LANDFILLED IN THE FIFTY STATES , 2014 .

[4]  F. Abnisa,et al.  A review on co-pyrolysis of biomass: An optional technique to obtain a high-grade pyrolysis oil , 2014 .

[5]  Dae-Hyun Shin,et al.  Liquid-phase catalytic degradation of mixtures of waste high-density polyethylene and polystyrene over spent FCC catalyst. Effect of mixing proportions of reactants , 2004 .

[6]  Amin Kalanatarifard,et al.  Identification of the Municipal Solid Waste Characteristics and Potential of Plastic Recovery at Bakri Landfill, Muar, Malaysia , 2012 .

[7]  W. Kaminsky.  Recycling of polymers by pyrolysis , 1993 .

[8]  J. Bhatti,et al.  ENERGY AND ECONOMIC VALUE OF NON- RECYCLED PLASTICS (NRP) AND MUNICIPAL SOLID WASTES (MSW) THAT ARE CURRENTLY LANDFILLED IN THE FIFTY STATES , 2011 .

[9]  Kunio Yoshikawa,et al.  Fuel Oil Production from Municipal Plastic Wastes in Sequential Pyrolysis and Catalytic Reforming Reactors , 2014 .

[10]  A. Pütün,et al.  Utilization of Two Different Types of Plastic Wastes from Daily and Industrial Life , 2013 .

[11]  Qiang Lu,et al.  Overview of fuel properties of biomass fast pyrolysis oils , 2009 .

[12]  M. Blazsó.  Composition of Liquid Fuels Derived from the Pyrolysis of Plastics , 2006 .

[13]  László Bartha,et al.  Thermal degradation of municipal plastic waste for production of fuel-like hydrocarbons , 2004 .

[14]  Eric Masanet,et al.  An assessment and prioritization of "design for recycling" guidelines for plastic components , 2002, Conference Record 2002 IEEE International Symposium on Electronics and the Environment (Cat. No.02CH37273).

[15]  T. Yoshioka,et al.  Pyrolysis of Mixed Plastics in a Fluidized Bed of Hard Burnt Lime , 2011 .

[16]  Isabel Cabrita,et al.  Pyrolysis of plastic wastes. 1. Effect of plastic waste composition on product yield , 1999 .

[17]  Mohammad Rehan,et al.  Effect of plastic waste types on pyrolysis liquid oil , 2017 .

[18]  H. M. Spiers.  Technical data on fuel , 1930 .

[19]  M. Al-Mamun,et al.  Pyrolytic Waste Plastic Oil and Its Diesel Blend: Fuel Characterization , 2016, Journal of environmental and public health.

[20]  Qinghai Li,et al.  Classification and comparison of municipal solid waste based on thermochemical characteristics , 2014, Journal of the Air & Waste Management Association.

[21]  Colin E. Snape,et al.  Recyling of plastic wastes via pyrolysis , 2000 .

[22]  H. Cornish,et al.  Toxicity of pyrolysis products of vinyl plastics. , 1969, Archives of environmental health.

[23]  W. Kaminsky,et al.  Olefins from polyolefins and mixed plastics by pyrolysis , 1995 .

[24]  Paul T. Williams,et al.  Analysis of products derived from the fast pyrolysis of plastic waste , 1997 .

[25]  Christian Roy,et al.  Vacuum pyrolysis of PVC I. Kinetic study , 1999 .

[26]  R. Meyer,et al.  Heavy Oil and Natural Bitumen : strategic petroleum resources , 2003 .

[27]  Wan Mohd Ashri Wan Daud,et al.  Optimizing the use of biomass waste through co-pyrolysis , 2017 .

[28]  W. Ahmad,et al.  Pyrolysis Study of Polypropylene and Polyethylene Into Premium Oil Products , 2015 .

[29]  Paul T. Williams,et al.  The pyrolysis of individual plastics and a plastic mixture in a fixed bed reactor , 1997 .

[30]  F. Abnisa,et al.  Recovery of liquid fuel from the aqueous phase of pyrolysis oil using catalytic conversion , 2014 .

[31]  P. Rutkowski,et al.  Influence of polystyrene addition to cellulose on chemical structure and properties of bio-oil obtained during pyrolysis , 2006 .

[32]  L. Sun,et al.  Thermal degradation of PVC: A review. , 2016, Waste management.

[33]  F. Abnisa,et al.  A review on pyrolysis of plastic wastes , 2016 .

[34]  Robert E. Dvorak,et al.  Plastics recycling: challenges and opportunities , 2009, Philosophical Transactions of the Royal Society B: Biological Sciences.

[35]  Paul T. Williams,et al.  Composition of products from the pyrolysis of polyethylene and polystyrene in a closed batch reactor: Effects of temperature and residence time , 2009 .