Long‐Term Operation of Nb‐Coated Stainless Steel Bipolar Plates for Proton Exchange Membrane Water Electrolyzers

Proton exchange membrane water electrolysis (PEMWE) is the most promising technology for green hydrogen production using renewable electricity, but it is expensive due to the Ti bipolar plates (BPPs). Herein, a PEMWE stack with coated stainless steel (ss) BPPs (Nb/Ti/ss‐BPP and Nb/ss‐BPP) is reported, which operates for about 14 000 h at 1.63 ± 0.12 A cm−2 and 65 °C. The average degradation rate is as low as 1.2% or 5.5 μV h−1. Scanning electrode microcopy reveals no signs of corrosion of the ss beneath the coatings. The interfacial contact resistance increases due to the formation of poorly conductive amorphous Nb oxides, as shown by atomic force microscopy and X‐Ray photoelectron spectroscopy, although it does not affect the cell performance. The results prove that Ti is not needed anymore as base material for manufacturing the BPPs, thus the cost of PEMWE can be significantly reduced.

[1]  K. Friedrich,et al.  Porous Transport Layers for Proton Exchange Membrane Electrolysis Under Extreme Conditions of Current Density, Temperature, and Pressure , 2021, Advanced Energy Materials.

[2]  C. Colominas,et al.  Coated stainless steels evaluation for bipolar plates in PEM water electrolysis conditions , 2021, International Journal of Hydrogen Energy.

[3]  T. Morawietz,et al.  Exploring the Interface of Skin‐Layered Titanium Fibers for Electrochemical Water Splitting , 2021, Advanced Energy Materials.

[4]  Andrea Kellenberger,et al.  Electrochemical Evaluation of Niobium Corrosion Resistance in Simulated Anodic PEM Electrolyzer Environment , 2020, International Journal of Electrochemical Science.

[5]  H. Gasteiger,et al.  Analysis of Gas Permeation Phenomena in a PEM Water Electrolyzer Operated at High Pressure and High Current Density , 2020, Journal of The Electrochemical Society.

[6]  F. Berkel,et al.  Novel components in Proton Exchange Membrane (PEM) Water Electrolyzers (PEMWE): Status, challenges and future needs. A mini review , 2020 .

[7]  Samuel Simon Araya,et al.  Long-term contamination effect of iron ions on cell performance degradation of proton exchange membrane water electrolyser , 2019, Journal of Power Sources.

[8]  K. Ayers,et al.  Perspectives on Low-Temperature Electrolysis and Potential for Renewable Hydrogen at Scale. , 2019, Annual review of chemical and biomolecular engineering.

[9]  Detlef Stolten,et al.  Initial approaches in benchmarking and round robin testing for proton exchange membrane water electrolyzers , 2019, International Journal of Hydrogen Energy.

[10]  Sandeep Kumar Dwivedi,et al.  Hydrogen embrittlement in different materials: A review , 2018, International Journal of Hydrogen Energy.

[11]  J. Kermode,et al.  Understanding and mitigating hydrogen embrittlement of steels: a review of experimental, modelling and design progress from atomistic to continuum , 2018, Journal of Materials Science.

[12]  Hartmut Spliethoff,et al.  Current status of water electrolysis for energy storage, grid balancing and sector coupling via power-to-gas and power-to-liquids: A review , 2018 .

[13]  M. Klell,et al.  Theoretical and experimental analysis of an asymmetric high pressure PEM water electrolyser up to 155 bar , 2017 .

[14]  Qi Feng,et al.  A review of proton exchange membrane water electrolysis on degradation mechanisms and mitigation strategies , 2017 .

[15]  Felix N. Büchi,et al.  High pressure polymer electrolyte water electrolysis: Test bench development and electrochemical analysis , 2017 .

[16]  K. A. Friedrich,et al.  Low-Cost and Durable Bipolar Plates for Proton Exchange Membrane Electrolyzers , 2017, Scientific Reports.

[17]  H. Karoliussen,et al.  Materials for Proton Exchange Membrane water electrolyzer bipolar plates , 2017 .

[18]  K. Ayers,et al.  Pathways to ultra-low platinum group metal catalyst loading in proton exchange membrane electrolyzers , 2016 .

[19]  K. A. Friedrich,et al.  Protective coatings on stainless steel bipolar plates for proton exchange membrane (PEM) electrolysers , 2016 .

[20]  K. Friedrich,et al.  Coated Stainless Steel Bipolar Plates for Proton Exchange Membrane Electrolyzers , 2016 .

[21]  Hui Li,et al.  PEM electrolysis for hydrogen production: principles and applications , 2015 .

[22]  D. Stolten,et al.  Validation and characterization of suitable materials for bipolar plates in PEM water electrolysis , 2015 .

[23]  B. Yi,et al.  The influence of Ferric ion contamination on the solid polymer electrolyte water electrolysis performance , 2015 .

[24]  Gareth Hinds,et al.  In situ characterisation of PEM water electrolysers using a novel reference electrode. , 2015 .

[25]  Feng-Yuan Zhang,et al.  Evaluation of nitrided titanium separator plates for proton exchange membrane electrolyzer cells , 2014 .

[26]  Zhigang Shao,et al.  Investigations on degradation of the long-term proton exchange membrane water electrolysis stack , 2014 .

[27]  Asif Ansar,et al.  Low Cost Bipolar Plates for Large Scale PEM Electrolyzers , 2014 .

[28]  D. Stolten,et al.  A comprehensive review on PEM water electrolysis , 2013 .

[29]  Z. Mao,et al.  Corrosion behavior of three bipolar plate materials in simulated SPE water electrolysis environment , 2012 .

[30]  Jong-Won Lee,et al.  A review of gas diffusion layer in PEM fuel cells: Materials and designs , 2012 .

[31]  COMMUNICATION FROM THE COMMISSION TO THE EUROPEAN PARLIAMENT, THE COUNCIL, THE EUROPEAN ECONOMIC AND SOCIAL COMMITTEE AND THE COMMITTEE OF THE REGIONS , 2008 .

[32]  E. Asselin,et al.  Corrosion of niobium in sulphuric and hydrochloric acid solutions at 75 and 95 °C , 2007 .

[33]  R. Simão,et al.  Titanium oxide films produced on commercially pure titanium by anodic oxidation with different voltages , 2007 .

[34]  Reiner Kirchheim,et al.  HYDROGEN IN METALS: Microstructural Aspects , 2006 .

[35]  R. Hesse,et al.  Peak shape analysis of core level photoelectron spectra using UNIFIT for WINDOWS , 1999 .