A three-dimensional heat conduction inverse procedure to investigate tool–chip thermal interaction in machining process

[1]  Hao Xu,et al.  An improved three-dimensional inverse heat conduction procedure to determine the tool-chip interface temperature in dry turning , 2013 .

[2]  Tarek Mabrouki,et al.  On the existence of a thermal contact resistance at the tool-chip interface in dry cutting of AISI 1045: Formation mechanisms and influence on the cutting process , 2013 .

[3]  A. Molinari,et al.  Contact variables and thermal effects at the tool–chip interface in orthogonal cutting , 2012 .

[4]  Suhas S. Joshi,et al.  An analytical model to predict specific shear energy in high-speed turning of Inconel 718 , 2009 .

[5]  Fabrizio Micari,et al.  On the evaluation of the global heat transfer coefficient in cutting , 2007 .

[6]  Albert J. Shih,et al.  A three-dimensional inverse problem in estimating the applied heat flux of a titanium drilling: Theoretical and experimental studies , 2007 .

[7]  Paul Mativenga,et al.  Characterization of machining of AISI 1045 steel over a wide range of cutting speeds. Part 2: Evaluation of flow stress models and interface friction distribution schemes , 2007 .

[8]  Shivakumar Raman,et al.  Observations of the tool–chip boundary conditions in turning of aluminum alloys , 2007 .

[9]  Fabrizio Micari,et al.  A critical analysis on the friction modelling in orthogonal machining , 2007 .

[10]  Álisson Rocha Machado,et al.  Temperature determination at the chip–tool interface using an inverse thermal model considering the tool and tool holder , 2006 .

[11]  Matthew S. Dargusch,et al.  Recommendations and guidelines for the performance of accurate heat transfer measurements in rapid forming processes , 2006 .

[12]  Fabrizio Micari,et al.  On the FE codes capability for tool temperature calculation in machining processes , 2006 .

[13]  W. Grzesik,et al.  Determination of temperature distribution in the cutting zone using hybrid analytical-FEM technique , 2006 .

[14]  Suresh V. Garimella,et al.  An experimentally validated thermo-mechanical model for the prediction of thermal contact conductance , 2005 .

[15]  Matthew S. Dargusch,et al.  Development of a non intrusive heat transfer coefficient gauge and its application to high pressure die casting , 2005 .

[16]  I. Jawahir,et al.  Finite element modeling of residual stresses in machining induced by cutting using a tool with finite edge radius , 2005 .

[17]  Xuejun Ren,et al.  Cutting temperatures in hard turning chromium hardfacings with PCBN tooling , 2004 .

[18]  Wit Grzesik,et al.  A computational approach to evaluate temperature and heat partition in machining with multilayer coated tools , 2003 .

[19]  Keith A. Woodbury,et al.  Inverse Engineering Handbook , 2002 .

[20]  Patrick Kwon,et al.  An inverse estimation scheme to measure steady-state tool–chip interface temperatures using an infrared camera , 2001 .

[21]  Wit Grzesik,et al.  The influence of thin hard coatings on frictional behaviour in the orthogonal cutting process , 2000 .

[22]  Herchang Ay,et al.  Heat transfer and life of metal cutting tools in turning , 1998 .

[23]  Jehnming Lin,et al.  Inverse estimation of the tool-work interface temperature in end milling , 1995 .

[24]  Paul K. Wright,et al.  A Remote Temperature Sensing Technique for Estimating the Cutting Interface Temperature Distribution , 1986 .

[25]  J. Jam,et al.  A NOVEL METHOD TO DETERMINE TOOL-CHIP THERMAL CONTACT CONDUCTANCE IN MACHINING , 2011 .

[26]  Takashi Ueda,et al.  On The Measurement of Temperature in Material Removal Processes , 2007 .

[27]  I. Korkut,et al.  The influence of feed rate and cutting speed on the cutting forces, surface roughness and tool–chip contact length during face milling , 2007 .

[28]  Wit Grzesik,et al.  Prediction of friction and heat flow in machining incorporating thermophysical properties of the coating–chip interface , 2004 .

[29]  W. Grzesik,et al.  Experimental investigation of the influence of adhesion on the frictional conditions in the cutting process , 1999 .