Impact of thin-walled high-strength steel structural sections

An experimental programme is reported which examines the progressive collapse behaviour of some thin-walled closed-section structural sections made from high-strength steels under quasi- static and impact axial loads. A comparison is made with theoretical formulae, which have been used successfully for predicting the behaviour of mild steel thin-walled structures. Ten quasi-static crush tests and 46 impact tests were conducted on spot-welded top-hat and laser- welded square sections. The thin-walled sections were made from two different types of high-strength steel and one mild steel, the mechanical properties of which were determined experimentally from quasi-static and dynamic tensile tests. Although no specific change in the collapse mode was observed, the limited weight-specific energy absorption e ciency of the high-strength steels under dynamic loadings hinders the weight-reduction potential of crashworthy designs. An unexpected difference in the structural effectiveness of spot-welded top-hat sections made from mild steels and high-strength steels was identified, but was not present for similar square sections. This difference further accentuated the loss in the advantage of high-strength steels over mild steels, especially for spot-welded top-hat sections, and led to differences in the agreement between the experimental results and the theoretical predictions.

[1]  D Mann.  ON MATERIALS FOR LEAN WEIGHT VEHICLES , 1998 .

[2]  N. Jones,et al.  Inertia effects in axisymmetrically deformed cylindrical shells under axial impact , 2000 .

[3]  T. Wierzbicki,et al.  On the Crushing Mechanics of Thin-Walled Structures , 1983 .

[4]  W. Abramowicz.  The effective crushing distance in axially compressed thin-walled metal columns , 1983 .

[5]  A. Jouet,et al.  Contribution of high strength steels to the absorption of impact energy , 1993 .

[6]  J. M. Alexander.  AN APPROXIMATE ANALYSIS OF THE COLLAPSE OF THIN CYLINDRICAL SHELLS UNDER AXIAL LOADING , 1960 .

[7]  Mark White,et al.  Experimental quasi-static axial crushing of top-hat and double-hat thin-walled sections , 1999 .

[8]  T. Wierzbicki,et al.  Axial Crushing of Multicorner Sheet Metal Columns , 1989 .

[9]  P. H. Thornton.  Energy absorption by structural collapse in dual phase steel tubes , 1979 .

[10]  M. J. Crooks,et al.  The Ultralight Steel Auto Body program completes phase I , 1996 .

[11]  S. Reid,et al.  Static and dynamic axial crushing of foam-filled sheet metal tubes , 1986 .

[12]  Norman Jones,et al.  Influence of spot-weld failure on crushing of thin-walled structural sections , 2003 .

[13]  M Rauser.  ENERGY ABSORPTION OF PASSENGER CAR BODY STRUCTURES MADE OF STEEL AND ALUMINIUM , 1986 .

[14]  In Young Yang,et al.  Axial Impact Collapse Analysis of Spot Welded Hat Shaped Section Members , 2001 .

[15]  Mark White,et al.  Experimental study into the energy absorbing characteristics of top-hat and double-hat sections subjected to dynamic axial crushing , 1999 .

[16]  Wlodek Abramowicz.  The Macro Element Approach in Crash Calculations , 1997 .

[17]  W. Abramowicz,et al.  Alexander revisited—A two folding elements model of progressive crushing of tubes , 1992 .

[18]  Matsuo Usuda,et al.  Absorbed energy during compression and crushing of high strength steel sheets , 1976 .

[19]  Norman Jones,et al.  Measurement of Impact Loads using a Laser Doppler Velocimeter , 1990 .

[20]  Norman Jones,et al.  Influence of stress waves on the dynamic progressive and dynamic plastic buckling of cylindrical shells , 2001 .

[21]  Norman Jones,et al.  Dynamic progressive buckling of circular and square tubes , 1986 .

[22]  Mark White,et al.  A theoretical analysis for the quasi-static axial crushing of top-hat and double-hat thin-walled sections , 1999 .

[23]  M. Langseth,et al.  Strain-rate sensitivity of mild steel grade St52-3N , 1991 .

[24]  S. Ashley.  Steel cars face a weighty decision , 1997 .

[25]  J. E. Scott,et al.  Energy Absorption of High-Strength Steel Tubes Under Impact Crush Conditions , 1977 .

[26]  R. G. Davies,et al.  Physical Metallurgy of Automotive High-Strength Steels , 1979 .

[27]  Mark White,et al.  A theoretical analysis for the dynamic axial crushing of top-hat and double-hat thin-walled sections , 1999 .