Miniaturization approach for EBG-based common mode filter and interference analysis

This paper describes the effort to miniaturize common mode filters based on electromagnetic bandgap structures. It describes the proposed approach by means of a systematic analysis of different configurations. The typical 3-patch configuration proposed in the past is modified removing the central patch and the bridge dimensions are tuned for keeping the same target frequency. The analysis of the crosstalk is carried out for the relevant configurations in order to assess the possible implementation of these structures in high density printed circuit boards. The simulation results are discussed and compared to identify the best miniaturized geometry for a practical implementation.

[1]  B. Archambeault,et al.  Compact configuration of a planar EBG based CM filter and crosstalk analysis , 2011, 2011 IEEE International Symposium on Electromagnetic Compatibility.

[2]  Tzong-Lin Wu,et al.  An Embedded Common-Mode Suppression Filter for GHz Differential Signals Using Periodic Defected Ground Plane , 2008, IEEE Microwave and Wireless Components Letters.

[3]  Barry Kent Gilbert,et al.  High-frequency characterization of power/ground-plane structures , 1999 .

[4]  T. Itoh,et al.  A Novel Wideband Common-Mode Suppression Filter for Gigahertz Differential Signals Using Coupled Patterned Ground Structure , 2009, IEEE Transactions on Microwave Theory and Techniques.

[5]  B. Archambeault,et al.  Optimum geometrical parameters for the EBG-based common mode filter design , 2012, 2012 IEEE International Symposium on Electromagnetic Compatibility.

[6]  S. Connor,et al.  Miniaturization of Common mode filter based on EBG patch resonance , 2012 .

[7]  F. Paulis,et al.  ACCURATE AND EFFICIENT ANALYSIS OF PLANAR ELECTROMAGNETIC BAND-GAP STRUCTURES FOR POWER BUS NOISE MITIGATION IN THE GHZ BAND , 2012 .

[8]  Xiaoxiong Gu,et al.  Experimental validation of an 8 GHz EBG based common mode filter and impact of manufacturing uncertainties , 2013, 2013 IEEE International Symposium on Electromagnetic Compatibility.

[9]  O.M. Ramahi,et al.  A simple and effective model for electromagnetic bandgap structures embedded in printed circuit boards , 2005, IEEE Microwave and Wireless Components Letters.

[10]  Tzong-Lin Wu,et al.  A Broadband and Miniaturized Common-Mode Filter for Gigahertz Differential Signals Based on Negative-Permittivity Metamaterials , 2010, IEEE Transactions on Microwave Theory and Techniques.

[11]  L Raimondo,et al.  A Simple and Efficient Design Procedure for Planar Electromagnetic Bandgap Structures on Printed Circuit Boards , 2011, IEEE Transactions on Electromagnetic Compatibility.

[12]  B. Archambeault,et al.  Common mode filtering performances of planar EBG structures , 2009, 2009 IEEE International Symposium on Electromagnetic Compatibility.

[13]  B. Mohajer-Iravani,et al.  Coupling reduction in enclosures and cavities using electromagnetic band gap structures , 2006, IEEE Transactions on Electromagnetic Compatibility.

[14]  Tzong-Lin Wu,et al.  Synthesis Model and Design of a Common-Mode Bandstop Filter (CM-BSF) With an All-Pass Characteristic for High-Speed Differential Signals , 2014, IEEE Transactions on Microwave Theory and Techniques.

[15]  Tzong-Lin Wu,et al.  Overview of Power Integrity Solutions on Package and PCB: Decoupling and EBG Isolation , 2010, IEEE Transactions on Electromagnetic Compatibility.

[16]  O.M. Ramahi,et al.  Electromagnetic interference (EMI) reduction from printed circuit boards (PCB) using electromagnetic bandgap structures , 2004, IEEE Transactions on Electromagnetic Compatibility.

[17]  Farzad Tavakkol-Hamedani,et al.  Electromagnetic Band gap Structures , 2007 .

[18]  Jun Fan,et al.  Mitigation of Noise Coupling in Multilayer High-Speed PCB: State of the Art Modeling Methodology and EBG Technology , 2010, IEICE Trans. Commun..