In situ tribometry of cold-sprayed Al-Al2O3 composite coatings

[1]  D. Fabijanic,et al.  The influence of Al2O3 reinforcement on the properties of stainless steel cold spray coatings , 2012 .

[2]  J. Legoux,et al.  The Effect of Deposition Conditions on Adhesion Strength of Ti and Ti6Al4V Cold Spray Splats , 2012, Journal of Thermal Spray Technology.

[3]  R. Chromik,et al.  Scaling effects between micro- and macro-tribology for a Ti–MoS2 coating , 2012 .

[4]  T. Scharf,et al.  Materials Phenomena Revealed by In Situ Tribometry , 2012, JOM.

[5]  R. Chromik,et al.  In situ tribology of nanocomposite Ti–Si–C–H coatings prepared by PE-CVD , 2011 .

[6]  J. Guilemany,et al.  Effect of the spraying process on the microstructure and tribological properties of bronze–alumina composite coatings , 2010 .

[7]  N. Birbilis,et al.  The influence of ceramic particles on bond strength of cold spray composite coatings on AZ91 alloy substrate , 2010 .

[8]  H. Koivuluoto,et al.  Structural Analysis of Cold-Sprayed Nickel-Based Metallic and Metallic-Ceramic Coatings , 2010 .

[9]  S. R. Bakshi,et al.  Microstructure and wear properties of aluminum/aluminum–silicon composite coatings prepared by cold spraying , 2009 .

[10]  Daniel Fabijanic,et al.  The use of Al–Al2O3 cold spray coatings to improve the surface properties of magnesium alloys , 2009 .

[11]  Mingxing Zhang,et al.  The use of kinetic metallization to form intermetallic reinforced composite coatings by post-spray heat treatment , 2009 .

[12]  W. Sawyer,et al.  Accessing Inaccessible Interfaces: In Situ Approaches to Materials Tribology , 2008 .

[13]  Eric Irissou,et al.  Review on Cold Spray Process and Technology: Part I—Intellectual Property , 2008 .

[14]  A. Sova,et al.  Deposition of multicomponent coatings by Cold Spray , 2008 .

[15]  J. Lüning,et al.  Run-In Behavior of Nanocrystalline Diamond Coatings Studied By in Situ Tribometry , 2008 .

[16]  S. R. Bakshi,et al.  Carbon nanotube reinforced aluminum composite coating via cold spraying , 2008 .

[17]  H. Liao,et al.  Effect of Ball Milling of Feedstock Powder on Microstructure and Properties of TiN Particle-Reinforced Al Alloy-Based Composites Fabricated by Cold Spraying , 2008 .

[18]  Wenya Li,et al.  Characterizations of Cold-Sprayed Nickel-Alumina Composite Coating with Relatively Large Nickel-Coated Alumina Powder , 2008, International Thermal Spray Conference.

[19]  Changhee Lee,et al.  The influence of process parameters on deposition characteristics of a soft/hard composite coating in kinetic spray process , 2008 .

[20]  Victor K. Champagne,et al.  The Cold Spray Materials Deposition Process : Fundamentals and Applications , 2007 .

[21]  C. Moreau,et al.  Investigation of Al-Al2O3 Cold Spray Coating Formation and Properties , 2007, International Thermal Spray Conference.

[22]  K. Wahl,et al.  In situ tribometry of solid lubricant nanocomposite coatings , 2007 .

[23]  Anatolii Papyrin,et al.  Cold Spray Technology , 2006 .

[24]  C. Schvezov,et al.  Wear of different aluminum matrix composites under conditions that generate a mechanically mixed layer , 2005 .

[25]  Tobias Schmidt,et al.  The cold spray process and its potential for industrial applications , 2005, Thermal Spray 2005: Proceedings from the International Thermal Spray Conference.

[26]  Jason E. Action,et al.  Wear-Rate Uncertainty Analysis , 2004 .

[27]  Y. Hong,et al.  Cold spray of SiC and Al2O3 with soft metal incorporation: A technical contribution , 2004 .

[28]  Hyun-Ki Kang,et al.  Tungsten/copper composite deposits produced by a cold spray , 2003 .

[29]  I. L. Singer,et al.  Role of third bodies in friction and wear of protective coatings , 2003 .

[30]  B. Venkataraman,et al.  Correlation between the characteristics of the mechanically mixed layer and wear behaviour of aluminium, Al-7075 alloy and Al-MMCs , 2000 .

[31]  A. Alpas,et al.  Wear mechanism maps for metal matrix composites , 1997 .

[32]  D. Rigney.  Comments on the sliding wear of metals , 1997 .

[33]  G. Sundararajan,et al.  The sliding wear behaviour of AlSiC particulate composites—I. Macrobehaviour , 1996 .

[34]  Ahmet T. Alpas,et al.  Effect of microstructure (particulate size and volume fraction) and counterface material on the sliding wear resistance of particulate-reinforced aluminum matrix composites , 1994 .

[35]  S. Schmauder,et al.  Elastic modulus and interface stress constraint of particle-reinforced composites , 1993 .

[36]  Maurice Godet,et al.  Third-bodies in tribology , 1990 .

[37]  A. R. Rosenfield,et al.  Wear processes in sliding systems , 1984 .

[38]  D. Rigney,et al.  Sliding wear and transfer , 1983 .

[39]  P. Blau.  Mechanisms for transitional friction and wear behavior of sliding metals , 1981 .

[40]  P. Morin,et al.  Electron–channelling imaging in scanning electron microscopy , 1979 .

[41]  Nam P. Suh,et al.  An overview of the delamination theory of wear , 1977 .

[42]  I. L. Singer,et al.  Monitoring Transfer Films and Friction Instabilities with In Situ Raman Tribometry , 2003 .

[43]  P. Stair,et al.  In situ studies of the lubricant chemistry and frictional properties of perfluoropolyalkyl ethers at a sliding contact , 2001 .

[44]  C. Subramanian,et al.  Dry sliding wear of aluminium composites : A review , 1997 .