Potentials for energy efficiency improvement in the US cement industry

This paper reports on an in-depth analysis of the US cement industry, identifying cost-effective energy efficiency measures and potentials. Between 1970 and 1997, primary physical energy intensity for cement production (SIC 324) dropped 30%, from 7.9 GJ/t to 5.6 GJ/t, while specific carbon dioxide emissions due to fuel consumption and clinker calcination dropped 17%, from 0.29 tC/tonne to 0.24 tC/tonne. We examined 30 energy-efficient technologies and measures and estimated energy savings, carbon dioxide savings, investment costs, and operation and maintenance costs for each of the measures. We constructed an energy conservation supply curve for the US cement industry which found a total cost-effective energy saving of 11% of 1994 energy use for cement making and a saving of 5% of total 1994 carbon dioxide emissions. Assuming the increased production of blended cement, the technical potential for energy efficiency improvement would not change considerably. However, the cost-effective potential would increase to 18% of total energy use, and carbon dioxide emissions would be reduced by 16%. This demonstrates that the use of blended cements is a key cost-effective strategy for energy efficiency improvement and carbon dioxide emission reductions in the US cement industry.

[1]  N. Patzelt,et al.  Finish grinding of slag , 1993 .

[2]  Anthony J. Buonicore,et al.  Air Pollution Engineering Manual , 1992 .

[3]  Ernst Worrell,et al.  Energy efficiency and carbon dioxide emissions reduction opportunities in the U.S. cement industry , 1999 .

[4]  C. W. Ruby.  A new approach to expert kiln control , 1997, 1997 IEEE/PCA Cement Industry Technical Conference. XXXIX Conference Record (Cat. No.97CH36076).

[5]  A. J. Kreisberg.  Selection and application of roller press for raw meal preparation at Alpena (cement plant) , 1992 .

[6]  A. Duplouy,et al.  Umbau und Optimierung der Drehofenanlagen im Werk Karsdorf der Lafarge Zement GmbH , 1997 .

[7]  J. Folsberg.  The air-swept ring roller mill for clinker grinding , 1997, 1997 IEEE/PCA Cement Industry Technical Conference. XXXIX Conference Record (Cat. No.97CH36076).

[8]  R. A. Somani,et al.  Die neue Zementlinie bei Rajashree Cement in Malkhed/Indien , 1997 .

[9]  K. Treanton,et al.  Revised 1996 IPCC guidelines for national greenhouse gas inventories. v. 1: Greenhouse gas inventory reporting instructions.- v. 2: Greenhouse gas inventory workbook.- v.3: Greenhouse gas inventory reference manual , 1997 .

[10]  H. E. Lowitt,et al.  The US cement industry: An energy perspective , 1988 .

[11]  G. Marchal,et al.  Industrial experience with clinker grinding in the HOROMILL/sup R/ , 1997, 1997 IEEE/PCA Cement Industry Technical Conference. XXXIX Conference Record (Cat. No.97CH36076).

[12]  J. Sirchis.  Energy Efficiency in the Cement Industry , 1990 .

[13]  M. J. Hutzler,et al.  Emissions of greenhouse gases in the United States , 1995 .

[14]  W. Ranze,et al.  Variable speed drives for roller presses , 1997, 1997 IEEE/PCA Cement Industry Technical Conference. XXXIX Conference Record (Cat. No.97CH36076).

[15]  R. Vidergar,et al.  Gyro-therm technology boosts cement kiln output, efficiency and cuts NO/sub x/ emissions , 1997, 1997 IEEE/PCA Cement Industry Technical Conference. XXXIX Conference Record (Cat. No.97CH36076).

[16]  Hiroshi Ueda,et al.  Gegenwärtiger Stand der Vormahlung von Klinker und Zementrohmaterialien nach dem CKP-System , 1992 .

[17]  H. E. Steuch,et al.  Ash Grove's new 2200 tpd Seattle plant comes on line , 1993 .

[18]  F. P. van der Vleuten.  Cement in development : energy and environment , 1994 .