Effects of engine variables and heat transfer on the performance of biodiesel fueled IC engines

These days internal combustion engines are the major source of transportation. They run mainly on fossil fuels which are depleting day by day not only that they cause pollution which endangers human life and creates environmental problems. Of late biodiesel has emerged as a better alternative fuel for internal combustion engines due to its comparable properties with that of fossil fuels. Today’s automobiles require economy of operation, high power output and last but not the least, reduction in greenhouse gases emitted by the vehicles. Such specific demands have compelled the researchers not only to focus on the parameters affecting the performance but also on emission of the internal combustion engines. This paper reviews the effects of different engine variables such as compression ratio, load and speed, fuel injection parameters, air swirl, piston design on the performance of engine. Special attention has been paid on the future automotive engines which would be significantly governed by electronic systems. According to us the same technology can also be employed in analyzing engines running on biofuels.

[1]  R. Sudhakaran,et al.  Comparative study of the combustion, performance, and emission characteristics of a variable compression ratio engine fuelled with diesel, corn oil methyl ester, and palm oil methyl ester , 2012 .

[2]  R. Udaya Kumar,et al.  Performance and Emission Analysis on a Direct Injection Diesel Engine Using Biodiesel From Palm Oil With Exhaust Gas Recirculation , 2005 .

[3]  R. Sudhakaran,et al.  Combustion and performance analysis of variable compression ratio engine fueled with preheated palm oil - diesel blends , 2013 .

[4]  M. M. El-Kassaby,et al.  The Impact of Changing the Compression Ratio on the Performance of an Engine fueled by Biodiesel Blends , 2013 .

[5]  H. Ng,et al.  Homogeneous Charge Compression Ignition (HCCI) combustion: Implementation and effects on pollutants in direct injection diesel engines , 2011 .

[6]  Adnan Parlak,et al.  The effect of heat transfer on performance of the Diesel cycle and exergy of the exhaust gas stream in a LHR Diesel engine at the optimum injection timing , 2005 .

[7]  Su Han Park,et al.  A study on the macroscopic spray behavior and atomization characteristics of biodiesel and dimethyl ether sprays under increased ambient pressure , 2010 .

[8]  Cristian Carraretto,et al.  Biodiesel as alternative fuel: Experimental analysis and energetic evaluations , 2004 .

[9]  A. Koca,et al.  Comparison of performance and emissions of diesel fuel, rapeseed and soybean oil methyl esters injected at different pressures , 2010 .

[10]  A. Demirbas,et al.  Biodiesel fuels from vegetable oils via catalytic and non-catalytic supercritical alcohol transesterifications and other methods: a survey , 2003 .

[11]  P. Devan,et al.  A study of the performance, emission and combustion characteristics of a compression ignition engine using methyl ester of paradise oil-eucalyptus oil blends , 2009 .

[12]  Olawole Abiola Kuti,et al.  Experimental and analytical study on biodiesel and diesel spray characteristics under ultra-high injection pressure , 2010 .

[13]  Mustafa Canakci,et al.  The influence of operating parameters on the performance and emissions of a DI diesel engine using methanol-blended-diesel fuel , 2010 .

[14]  Graham T. Reader,et al.  Biodiesel engine performance and emissions in low temperature combustion , 2008 .

[15]  Gvidonas Labeckas,et al.  Performance and emission characteristics of a direct injection diesel engine operating on KDV synthetic diesel fuel , 2013 .

[16]  K. A. Subramanian,et al.  Utilization of liquid biofuels in automotive diesel engines: An Indian perspective , 2005 .

[17]  R. M. Sarviya,et al.  Impact of alternative fuel properties on fuel spray behavior and atomization , 2012 .

[18]  Wojciech M. Budzianowski,et al.  Effects of compression ratio, swirl augmentation techniques and ethanol addition on the combustion of CNG–biodiesel in a dual-fuel engine , 2014 .

[19]  Song-Charng Kong,et al.  Characteristics of Engine Emissions Using Biodiesel Blends in Low-Temperature Combustion Regimes , 2008 .

[20]  D. Vasudevan,et al.  Performance, emission and combustion characteristics of a variable compression ratio engine using methyl esters of waste cooking oil and diesel blends , 2011 .

[21]  H. Masjuki,et al.  Biodiesel from palmoil—an analysis of its properties and potential , 2002 .

[22]  Ta-Jen Huang,et al.  NOx emission control for automotive lean-burn engines by electro-catalytic honeycomb cells , 2012 .

[23]  Katsuhiko Takeuchi,et al.  Ultra high pressure and enhanced multiple injection – potentials for the diesel engine and challenge for the fuel injection system , 2012 .

[24]  A. I. Ogbonna,et al.  Effect of advanced injection timing on the performance of rapeseed oil in diesel engines , 2000 .

[25]  B. V. Appa Rao,et al.  Reduction of NOx in the exhaust gas of DI- diesel engine fueled with mahua methyl ester along with exhaust gas recirculation , 2009 .

[26]  Aiyagari Ramesh,et al.  Effect of compression ratio on the performance and combustion of a biogas fuelled spark ignition engine , 2012 .

[27]  A. Maghbouli,et al.  Effects of piston bowl geometry on combustion and emission characteristics of biodiesel fueled diesel engines , 2014 .

[28]  S. P. Sivapirakasam,et al.  Investigation on the effect of injection system parameters on performance and emission characteristics of a twin cylinder compression ignition direct injection engine fuelled with pongamia biodiesel–diesel blend using response surface methodology , 2011 .

[29]  K. Annamalai,et al.  Combined effect of injection timing and combustion chamber geometry on the performance of a biodiesel fueled diesel engine , 2012 .

[30]  Adnan Parlak,et al.  Performance characteristics of a low heat rejection diesel engine operating with biodiesel , 2008 .

[31]  N. Nahar,et al.  Prospects and potential of fatty acid methyl esters of some non-traditional seed oils for use as biodiesel in India , 2005 .

[32]  Avinash Kumar Agarwal,et al.  Performance, emissions and combustion characteristics of Karanja biodiesel in a transportation engine , 2014 .

[33]  G. R. Kannan,et al.  Effect of injection pressure and injection timing on DI diesel engine fuelled with biodiesel from waste cooking oil , 2012 .

[34]  Su Han Park,et al.  A study on the fuel injection and atomization characteristics of soybean oil methyl ester (SME) , 2009 .

[35]  Hifjur Raheman,et al.  Performance of diesel engine with biodiesel at varying compression ratio and ignition timing , 2008 .

[36]  Mustafa Canakci,et al.  The impact of fuel injection pressure on the exhaust emissions of a direct injection diesel engine fueled with biodiesel–diesel fuel blends , 2012 .

[37]  K. Kumar,et al.  Effect of exhaust gas recirculation and ethyl hexyl nitrate additive on biodiesel fuelled diesel engine for the reduction of NOx emissions , 2012 .

[38]  G. Lakshmi Narayana Rao,et al.  Effect of Combustion Chamber Design on a DI Diesel Engine Fuelled with Jatropha Methyl Esters Blends with Diesel , 2013 .

[39]  H. E. Saleh Effect of exhaust gas recirculation on diesel engine nitrogen oxide reduction operating with jojoba methyl ester. , 2009 .

[40]  Balaji Mohan,et al.  Optimization of biodiesel fueled engine to meet emission standards through varying nozzle opening pressure and static injection timing , 2014 .

[41]  Hüseyin Aydın,et al.  Improving the usability of vegetable oils as a fuel in a low heat rejection diesel engine , 2012 .

[42]  Filiz Karaosmanoglu,et al.  Engine and winter road test performances of used cooking oil originated biodiesel. , 2005 .

[43]  S. Jayaraj,et al.  Theoretical modeling and experimental studies on biodiesel-fueled engine , 2006 .

[44]  B. Durga Prasad,et al.  An Extraction and Performance Analysis of Rubber Seed-Methyl Ester on an IC Engine at Various Compression Ratios , 2014 .

[45]  S. Sivaprakasam,et al.  Experimental Analysis of Exhaust Gas Recirculation on DI Diesel Engine Operating with Biodiesel , 2013 .

[46]  I. M. Rizwanul Fattah,et al.  Production and comparison of fuel properties, engine performance, and emission characteristics of biodiesel from various non-edible vegetable oils: A review , 2014 .

[47]  S. K. Bhatti,et al.  Optimization strategies to reduce the biodiesel NOx effect in diesel engine with experimental verification , 2013 .

[48]  G. Nagarajan,et al.  Influence of injection timing on performance, emission and combustion characteristics of a DI diesel engine running on waste plastic oil , 2009 .

[49]  Dimitrios C. Rakopoulos,et al.  Development and application of multi-zone model for combustion and pollutants formation in direct injection diesel engine running with vegetable oil or its bio-diesel , 2007 .

[50]  Dimitrios C. Rakopoulos,et al.  Multi-zone modeling of Diesel engine fuel spray development with vegetable oil, bio-diesel or Diesel fuels , 2006 .

[51]  Walter Knecht,et al.  Diesel engine development in view of reduced emission standards , 2008 .

[52]  K. Annamalai,et al.  Effects of open combustion chamber geometries on the performance of pongamia biodiesel in a DI diesel engine , 2012 .

[53]  R. Gakkhar,et al.  Influence of injection timing on performance, combustion and emission characteristics of Jatropha biodiesel engine , 2011 .

[54]  Arántzazu Gómez,et al.  Biodiesel Emissions from a Baseline Engine Operated with Different Injection Systems and Exhaust Gas Recirculation (EGR) Strategies during Transient Sequences , 2009 .

[55]  Anoop Dixit,et al.  Performance characteristics of Jatropha ethyl ester as diesel engine fuel at different compression ratios , 2013 .

[56]  Seung Hwan Bang,et al.  Fuel injection characteristics and spray behavior of DME blended with methyl ester derived from soybean oil , 2010 .

[57]  N. V. Deshpande,et al.  Overview of EGR, Injection Timing and Pressure on Emissions and Performance of CI Engine with Pongamia Methyl Ester , 2005 .

[58]  A. Agarwal,et al.  Effect of Exhaust Gas Recirculation (EGR) on performance, emissions, deposits and durability of a constant speed compression ignition engine , 2011 .

[59]  C. D. Rakopoulos,et al.  Performance and emissions of bus engine using blends of diesel fuel with bio-diesel of sunflower or cottonseed oils derived from Greek feedstock , 2008 .

[60]  Saiful Bari,et al.  Effect of Fuel injection timing with waste cooking oil as a fuel in a direct injection diesel engine , 2004 .

[61]  N. Alagumurthi,et al.  Performance and emission studies on biofuel-powered Kirloskar TV-1 direct-injection diesel engine with exhaust gas recirculation , 2011 .

[62]  Haji Hassan Masjuki,et al.  A comprehensive review on biodiesel as an alternative energy resource and its characteristics , 2012 .

[63]  Haji Hassan Masjuki,et al.  Properties and use of Moringa oleifera biodiesel and diesel fuel blends in a multi-cylinder diesel engine , 2014 .

[64]  Nagaraj R. Banapurmath,et al.  Effect of biodiesel derived from Honge oil and its blends with diesel when directly injected at different injection pressures and injection timings in single-cylinder water-cooled compression ignition engine , 2009 .

[65]  Andreas Pfeifer,et al.  A New Approach to Boost Pressure and EGR Rate Control Development for HD Truck Engines with VGT , 2002 .

[66]  A. E. Atabani,et al.  Recent scenario and technologies to utilize non-edible oils for biodiesel production , 2014 .

[67]  T. Mohanraj,et al.  Operating Characteristics of a Variable Compression Ratio Engine Using Esterified Tamanu Oil , 2013 .

[68]  Jerekias Gandure,et al.  Comparative performance analysis of marula oil and petrodiesel fuels on a variable compression ratio engine , 2011, IEEE Africon '11.

[69]  A. Tsolakis,et al.  Engine performance and emissions of a diesel engine operating on diesel-RME (rapeseed methyl ester) blends with EGR (exhaust gas recirculation) , 2007 .

[70]  G. Lakshmi Narayana Rao,et al.  Experimental Studies on the Combustion and Emission Characteristics of a Diesel Engine Fuelled with Used Cooking Oil Methyl Esterand its Diesel Blends , 2008 .

[71]  Zoran Filipi,et al.  The Impact of Exhaust Gas Recirculation on Performance and Emissions of a Heavy-Duty Diesel Engine , 2003 .

[72]  Octavio Armas,et al.  Effect of biodiesel fuels on diesel engine emissions , 2008 .

[73]  Y.zh. Bian,et al.  Experimental studies on the combustion characteristics and performance of a direct injection engine fueled with biodiesel/diesel blends , 2010 .

[74]  Metin Gumus,et al.  A comprehensive experimental investigation of combustion and heat release characteristics of a biodiesel (hazelnut kernel oil methyl ester) fueled direct injection compression ignition engine , 2010 .

[75]  H. K. Amarnath,et al.  A Comparative Analysis of Thermal Performance And Emission Characteristics of Methyl Esters of Karanja And Jatropha Oils Based on A Variable Compression Ratio Diesel Engine , 2014 .

[76]  M. A. Fazal,et al.  Biodiesel feasibility study: An evaluation of material compatibility; performance; emission and engine durability , 2011 .

[77]  Wenming Yang,et al.  Combustion and emissions characteristics of diesel engine fueled by biodiesel at partial load conditions , 2012 .

[78]  John B. Heywood,et al.  Internal combustion engine fundamentals , 1988 .

[79]  G. Devaradjane,et al.  Experimental investigation of effect of compression ratio, injection timing and injection pressure on the performance of a CI engine operated with diesel-pungam methyl ester blend , 2010, Frontiers in Automobile and Mechanical Engineering -2010.

[80]  Rathnaraj David Jebamani,et al.  Studies on variable swirl intake system for DI diesel engine using computational fluid dynamics , 2008 .

[81]  Vilmar Æsøy,et al.  Combustion and emissions characteristics of fish oil fuel in a heavy-duty diesel engine , 2013 .

[82]  Helmut Eichlseder,et al.  POTENTIAL OF IC-ENGINES AS MINIMUM EMISSION PROPULSION SYSTEM , 2003 .

[83]  K. A. Subramanian,et al.  Comparative evaluations of injection and spray characteristics of a diesel engine using karanja biodiesel–diesel blends , 2013 .

[84]  Yuzo Aoyagi,et al.  Effect of Exhaust Gas Recirculation on Exhaust Emissions from Diesel Engines Fuelled with Biodiesel , 2007 .

[85]  Haji Hassan Masjuki,et al.  Effect of idling on fuel consumption and emissions of a diesel engine fueled by Jatropha biodiesel blends , 2014 .

[86]  Medhat A. Nemitallah,et al.  Studying the effect of compression ratio on an engine fueled with waste oil produced biodiesel/diesel fuel , 2013 .

[87]  P. Raman,et al.  Performance analysis of an internal combustion engine operated on producer gas, in comparison with the performance of the natural gas and diesel engines , 2013 .

[88]  Md. Nurun Nabi,et al.  Theoretical and experimental investigation of diesel engine performance, combustion and emissions analysis fuelled with the blends of ethanol, diesel and jatropha methyl ester , 2012 .

[89]  M. G. Dastidar,et al.  Performance Improvement and Emissions Reduction of a DI Diesel Engine for use of Karanja Biodiesel-Diesel Blend (B20) Using Diethyl Ether , 2011 .

[90]  Michael T. Leick,et al.  Effect of EGR and injection timing on combustion and emission characteristics of split injection strategy DI-diesel engine fueled with biodiesel , 2011 .

[91]  Avinash Kumar Agarwal,et al.  Biofuels (alcohols and biodiesel) applications as fuels for internal combustion engines , 2007 .

[92]  G. Labeckas,et al.  THE EFFECT OF RAPESEED OIL METHYL ESTER ON DIRECT INJECTION DIESEL ENGINE PERFORMANCE AND EXHAUST EMISSIONS , 2006 .

[93]  T. Balusamy,et al.  Effect of Injection Time and Injection Pressure on CI Engine Fuelled with Methyl Ester of Thevetia Peruviana Seed Oil , 2010 .

[94]  B. Pla,et al.  Effects of low pressure exhaust gas recirculation on regulated and unregulated gaseous emissions dur , 2011 .

[95]  Seinosuke Hara,et al.  Study of fuel economy improvement through control of intake valve closing timing : cause of combustion deterioration and improvement , 1995 .

[96]  S. Jayaraj,et al.  Performance and emission studies on biodiesel-liquefied petroleum gas dual fuel engine with exhaust gas recirculation , 2010 .

[97]  Su Han Park,et al.  Effects of multiple-injection strategies on overall spray behavior, combustion, and emissions reduction characteristics of biodiesel fuel , 2011 .

[98]  S. P. Sivapirakasam,et al.  Comparative studies on fly ash coated low heat rejection diesel engine on performance and emission c , 2011 .

[99]  G. Nagarajan,et al.  Effect of injection pressure on performance, emission and combustion characteristics of high linolenic linseed oil methyl ester in a DI diesel engine , 2009 .

[100]  A. Bulent Koc,et al.  Performance and NOx emissions of a diesel engine fueled with biodiesel-diesel-water nanoemulsions , 2013 .

[101]  Sibendu Som,et al.  A comparison of injector flow and spray characteristics of biodiesel with petrodiesel , 2010 .

[102]  Mohammed A. Hamdan,et al.  Simulation of compression engine powered by Biofuels , 2010 .

[103]  P. Tamilporai,et al.  Analysis of combustion, performance and emission characteristics of low heat rejection engine using biodiesel , 2010 .

[104]  K. Subramanian A comparison of water–diesel emulsion and timed injection of water into the intake manifold of a diesel engine for simultaneous control of NO and smoke emissions , 2011 .

[105]  Nagaraj R. Banapurmath,et al.  Performance studies of a low heat rejection engine operated on non-volatile vegetable oils with exhaust gas recirculation , 2009 .

[106]  Dimitrios C. Rakopoulos,et al.  Multi-zone modeling of combustion and emissions formation in DI diesel engine operating on ethanol–diesel fuel blends , 2008 .

[107]  S. Kent Hoekman,et al.  Review of the effects of biodiesel on NOx emissions , 2012 .

[108]  Ryutaro Komiya,et al.  Japan's macroeconomic performance since the first oil crisis: Review and appraisal , 1984 .

[109]  N. S. Rathore,et al.  Experimental investigation of the effect of compression ratio and injection pressure in a direct injection diesel engine running on Jatropha methyl ester , 2010 .

[110]  B. Desmet,et al.  Characterisation of very high pressure diesel sprays using digital imaging techniques , 2005 .