Aluminium Based Material Extrusion Through Mathematical Contoured Die: Numerical & Experimental Investigation

The metal forming process is preferable for manufacturing the parts of moderate complexity and greatly diversified profiles for the larger volume of productions to reduce the tooling cost. Energy saving, less scrap generation and near net shape production with better mechanical properties along with high production rate have enhanced the specific forming process, extrusion, for the production of long straight metal products. The huge demand of aluminium alloy in the extrusion industry for fulfilling the market requirements in the sector of building and architecture, construction, automobile and transport system, electrical and electronics, aerospace, and heat exchangers tends to optimize the process for improved process efficiency as well as product quality. Prediction of the influence of process parameters is very difficult owing to the concealed material deformation during extrusion. Due to this reason, an illustrious finite element analysis tool (DEFORM TM) was adopted to investigate the process. The simulations were performed to ascertain extrusion load, effective stress, effective strain and temperature distribution for square to square extrusion process. To decipher the effect of die length, ram velocity and extrusion ratio in the process, simulations were carried out by varying the variables in a wide range with different types of dies. The process was also employed for the investigation of the round to square extrusion considering the same parameters along with punch shape for Al-6063 alloy. Influence of die profile plays a predominant role in predicting the ultimate load requirements and flow characteristics. Considering the die profile an important component, the profile for round to square shape has been developed by following cosine, linear converging, elliptic, hyperbolic and 3rd order polynomial laws. Considering the above die profiles the simulations were conducted with optimised process parameters to find out a suiatable die profile. The simulations were validated with high-temperature experimentations. To improve the product properties, aluminium metal matrix composites (AMMC) prepared by powder metallurgy (PM) route has been extruded. Four different reinforcing elements of 2 wt. % (Zn, Ti, Soda lime silica glass and ZrO2) were added to Al / 5 wt. % of Mg / 1 wt. % of Gr matrix. To avoid the product defects, mathematically contoured cosine profiled die was used for the thermo-mechanical treatment. The improvement of the product properties has been studied. The optimum parameters before experimentation can be set by utilising the finite element tool successfully. Computerised finite element techniques are the best suitable technique to understand the concealed operations like extrusion. The optimum ranges for the extrusion of simple square bar section from the same shape billet and round to square extrusion has been established. The cosine profiled die for both kinds of extrusion as well as PM composite was found suitable as it generates lesser velocity relative difference at die exit. A significant amount of property improvement was observed in the AMMC after thermo-mechanical treatment.

[1]  Hui Zhao,et al.  Simulation of extrusion process of complicated aluminium profile and die trial , 2012 .

[2]  T. Aukrust,et al.  Studies of the mechanisms for buckling and waving in aluminum extrusion by use of a lagrangian FEM software , 2006 .

[3]  A. Baradeswaran,et al.  Wear and mechanical characteristics of Al 7075/graphite composites , 2014 .

[4]  Abbas Najafizadeh,et al.  A new method for evaluation of friction in bulk metal forming , 2004 .

[5]  I. Flitta,et al.  Nature of friction in extrusion process and its effect on material flow , 2003 .

[6]  W. S. Miller,et al.  Recent development in aluminium alloys for the automotive industry , 2000 .

[7]  S. Seshadri,et al.  A model for wear rates of composite coatings , 1992 .

[8]  A. K. Rout,et al.  Numerical and experimental study on the three-dimensional extrusion of square section from square billet through a polynomial shaped curved die , 2011 .

[9]  A. Rabiei,et al.  Fracture behavior of particle reinforced metal matrix composites , 2008 .

[10]  Karen Abrinia,et al.  An analytical formulation as an alternative to FEM software giving strain and stress distributions for the three-dimensional solution of extrusion problems , 2014 .

[11]  Jun Liang Liu,et al.  Investigation on microstructures and interface character of B4C particles reinforced 2024Al matrix composites fabricated by mechanical alloying , 2008 .

[12]  Design and analysis of optimal die profile for the extrusion of round SiC DRMM Al 6061 composite billet into hexagonal section , 2015 .

[13]  Yi Han,et al.  Hot deformation behavior of 7150 aluminum alloy during compression at elevated temperature , 2009 .

[14]  T. Sheppard.  Temperature and speed effects in hot extrusion of aluminium alloys , 1981 .

[15]  Wencai Liu,et al.  Effect of hot extrusion on wear properties of Al–15 wt.% Mg2Si in situ metal matrix composites , 2014 .

[16]  W. S. Miller,et al.  Recent development in aluminium alloys for aerospace applications , 2000 .

[17]  G. Abouelmagd.  Hot deformation and wear resistance of P/M aluminium metal matrix composites , 2004 .

[18]  C. Venkatesh,et al.  Design and analysis of streamlined extrusion die for round to hexagon using area mapping technique, upper bound technique and finite element method , 2014 .

[19]  José M. Torralba,et al.  Microstructural and mechanical characterisation of 7075 aluminium alloy consolidated from a premixed powder by cold compaction and hot extrusion , 2014 .

[20]  J. Ni,et al.  Size effects in thin sheet metal forming and its elastic–plastic constitutive model , 2007 .

[21]  Ramin Ebrahimi,et al.  Analysis of forward–backward-radial extrusion process , 2009 .

[22]  Boris Štok,et al.  Tool design optimization in extrusion processes , 1998 .

[23]  O. El-Kady,et al.  Effect of SiC particle size on the physical and mechanical properties of extruded Al matrix nanocomposites , 2014 .

[24]  Rajesh Ransing,et al.  An innovative extrusion die layout design approach for single-hole dies , 2009 .

[25]  Jie Zhou,et al.  Prediction of temperature evolution during the extrusion of 7075 aluminium alloy at various ram speeds by means of 3D FEM simulation , 2004 .

[26]  Yong-Taek Im,et al.  Analysis and design of flat-die hot extrusion process - 1. Three-dimensional finite element analysis , 2002 .

[27]  T. Sheppard.  Extrusion of Aluminium Alloys , 1999 .

[28]  J. R. Pickens.  Aluminium powder metallurgy technology for high-strength applications , 1981 .

[29]  Jean-Pierre Celis,et al.  Velocity effects on the wear, friction and tribochemistry of aluminum MMC sliding against phenolic brake pad , 2004 .

[30]  Jie Zhou,et al.  FEM simulation of aluminium extrusion through two-hole multi-step pocket dies , 2009 .

[31]  M. Ramachandra,et al.  Effect of reinforcement of flyash on sliding wear, slurry erosive wear and corrosive behavior of aluminium matrix composite , 2007 .

[32]  J. Torralba,et al.  P/M aluminum matrix composites: an overview , 2003 .

[33]  Patrick Ulysse.  Optimal extrusion die design to achieve flow balance , 1999 .

[34]  Mohammad Bakhshi-Jooybari,et al.  A theoretical and experimental study of friction in metal forming by the use of the forward extrusion process , 2002 .

[35]  C.-T. T. Hsu,et al.  Measurement of friction and the flow stress of steels at room and elevated temperatures by ring-compression tests , 1993 .

[36]  L. Dobrzański,et al.  Mechanically milled AA6061/(Ti3Al)P MMC reinforced with intermetallics – the structure and properties , 2004 .

[37]  R. Narayanasamy,et al.  Effect of Glass and SiC in Aluminum matrix on workability and strain hardening behavior of powder metallurgy hybrid composites , 2012 .

[38]  K. Saanouni,et al.  Numerical simulation of bursting in extrusion process using finite viscoplasticity with ductile damage and thermal effects , 2009 .

[39]  S. Panigrahi,et al.  Transformation of cast A356 ingots to wrought sheets with enhanced mechanical and tribological properties by different thermo-mechanical processing routes , 2016 .

[40]  Guoqun Zhao,et al.  Optimization of an aluminum profile extrusion process based on Taguchi’s method with S/N analysis , 2012 .

[41]  M. Emamy,et al.  Effects of extrusion temperature on the microstructure and tensile properties of Al–16 wt% Al4Sr metal matrix composite , 2013 .

[42]  W. Marsden.  I and J , 2012 .

[43]  A. T. Male,et al.  A Method for the Determination of the Coefficient of Friction of Metals under Conditions of Bulk Plastic Deformation , 1964 .

[44]  Meng-jun Wang,et al.  Deformation simulation of low-temperature high-speed extrusion for 6063 Al alloy , 2010 .

[45]  A. Khosravifard,et al.  Investigation of parameters affecting interface strength in Al/Cu clad bimetal rod extrusion process , 2010 .

[46]  J Lof,et al.  FEM simulations of the extrusion of complex thin-walled aluminium sections , 2002 .

[47]  M. Alizadeh,et al.  Synthesis behavior of nanocrystalline Al–Al2O3 composite during low time mechanical milling process , 2011 .

[48]  Lihua Zhu,et al.  Computer simulation of the deep extrusion of a thin-walled cup using the thermo-mechanically coupled elasto-plastic FEM , 2000 .

[49]  R. Narayanasamy,et al.  Effect of glass in aluminum matrix on workability and strain hardening behavior of powder metallurgy composite , 2011 .

[50]  B. Avitzur,et al.  Measurement of Friction in Drawing, Extrusion, and Rolling , 1968 .

[51]  Mohammad Bakhshi-Jooybari,et al.  Experimental and numerical study of optimal die profile in cold forward rod extrusion of aluminum , 2005 .

[52]  Jie Zhou,et al.  Extrusion of 7075 aluminium alloy through double-pocket dies to manufacture a complex profile , 2009 .

[53]  Byeong-Woo Kim,et al.  Optimal die profile design for uniform microstructure in hot extruded product , 2000 .

[54]  Joeri Lof,et al.  Developments in finite element simulations of aluminium extrusion , 2000 .

[55]  Mohammad Bakhshi-Jooybari,et al.  Combined upper bound and slab method, finite element and experimental study of optimal die profile in extrusion , 2007 .

[56]  B. Sridhara,et al.  Wear characteristics of hybrid aluminium matrix composites reinforced with graphite and silicon carbide particulates , 2010 .

[57]  Jie Zhou,et al.  3D FEM simulation of the whole cycle of aluminium extrusion throughout the transient state and the steady state using the updated Lagrangian approach , 2003 .

[58]  Chung-Gil Kang,et al.  Die design optimization for axisymmetric hot extrusion of metal matrix composites , 2001 .

[59]  Nikolai Biba,et al.  Cost effective implementation of forging simulation , 2001 .

[60]  Xavier Velay,et al.  Application of finite element method in the hot extrusion of aluminium alloys , 2004 .

[61]  Y. Mahajan,et al.  EFFECT OF EXTRUSION PARAMETERS ON STRUCTURE AND PROPERTIES OF 2124 ALUMINUM ALLOY MATRIX COMPOSITES , 2001 .

[62]  Dyi-Cheng Chen,et al.  Investigation into cold extrusion of aluminum billets using three-dimensional finite element method , 2007 .

[63]  E. Akinlabi,et al.  Effect of Punch Diameters on Shear Extrusion of 6063 Aluminium Alloy , 2015 .

[64]  Liliang Wang,et al.  Friction in aluminium extrusion—part 2: A review of friction models for aluminium extrusion , 2012 .

[65]  E. Sánchez,et al.  Mechanical characterisation of AA7015 aluminium alloy reinforced with ceramics , 2003 .

[66]  K. Abrinia,et al.  Process Parameter Investigations of Backward Extrusion for Various Aluminum Shaped Section Tubes Using FEM Analysis , 2011 .

[67]  J. Duszczyk,et al.  Predicting the variation of the exit temperature with the initial billet temperature during extrusion to produce an AZ31 profile , 2009 .

[68]  H. Valberg,et al.  Applied Metal Forming: Including FEM Analysis , 2010 .

[69]  Hao Chen,et al.  Numerical simulation and metal flow analysis of hot extrusion process for a complex hollow aluminum profile , 2012 .

[70]  A. Mazahery,et al.  Application of the Extrusion to Increase the Binding between the Ceramic Particles and the Metal Matrix: Enhancement of Mechanical and Tribological Properties , 2013 .

[71]  G. K. Lal,et al.  Viscoplastic deformation analysis and extrusion die design by FEM , 1991 .

[72]  C. Kang,et al.  Effects of hot extrusion through a curved die on the mechanical properties of SiCp/Al composites fabricated by melt-stirring , 1999 .

[73]  Mohammad Bakhshi-Jooybari,et al.  Experimental and numerical study of energy consumption in forward and backward rod extrusion , 2006 .

[74]  Dae-gun Kim,et al.  Sintering characteristic of Al2O3-reinforced 2xxx series Al composite powders , 2005 .