Effect of exposure time on curing efficiency of polymerizing units equipped with light-emitting diodes.

A study was conducted to evaluate the top and bottom hardness of two composites cured using polymerizing units equipped with light-emitting diodes [LED] (LEDemetron; Elipar FreeLight, Coltolux LED) and one quartz-tungsten halogen device [QTH] (Optilux 501) under different exposure times (20, 40 and 60 sec). A matrix mold 5 mm in diameter and 2 mm in depth was made to obtain five disc-shaped specimens for each experimental group. The specimens were cured by one of the light-curing units (LCUs) for 20, 40 or 60 sec, and the hardness was measured with a Vickers hardness-measuring instrument (50 g/30 sec). Data were subjected to three-way ANOVA and Tukey's test (alpha = 0.05). LED LCUs were as effective as the QTH device for curing both composites. A significant increase in the microhardness values were observed for all light LCUs when the exposure time was changed from 20 sec to 40 sec. The Z250 composite showed hardness values that were usually higher than those of the Charisma composite under similar experimental conditions. LED LCUs are as efficient for curing composites as the QTH device as long as an exposure time of 40 sec or higher is employed. An exposure time of 40 sec is required to provide composites with a uniform and high Knoop hardness when LED light-curing units are employed.

[1]  K. Jandt,et al.  Knoop hardness depth profiles and compressive strength of selected dental composites polymerized with halogen and LED light curing technologies. , 2002, Journal of biomedical materials research.

[2]  E. Greener,et al.  Effect of photoinitiator on degree of conversion of unfilled light-cured resin. , 1994, Journal of dentistry.

[3]  Sung-Ho Park,et al.  Curing units' ability to cure restorative composites and dual-cured composite cements under composite overlay. , 2004, Operative dentistry.

[4]  P. Andreou,et al.  Evaluation of a second-generation LED curing light. , 2003, Journal.

[5]  B. Hugo,et al.  Effect of irradiation type (LED or QTH) on photo-activated composite shrinkage strain kinetics, temperature rise, and hardness. , 2002, European journal of oral sciences.

[6]  K. Jandt,et al.  Photoinitiator dependent composite depth of cure and Knoop hardness with halogen and LED light curing units. , 2003, Biomaterials.

[7]  P. Andreou,et al.  Comparison of quartz-tungsten-halogen, light-emitting diode, and plasma arc curing lights. , 2003, The journal of adhesive dentistry.

[8]  M. Kidd,et al.  Effect of LED curing on the microleakage, shear bond strength and surface hardness of a resin-based composite restoration. , 2005, Biomaterials.

[9]  A. Yap,et al.  Effectiveness of composite cure associated with different curing modes of LED lights. , 2003, Operative dentistry.

[10]  E Asmussen,et al.  Influence of UEDMA BisGMA and TEGDMA on selected mechanical properties of experimental resin composites. , 1998, Dental materials : official publication of the Academy of Dental Materials.

[11]  C. Kleverlaan,et al.  Curing efficiency and heat generation of various resin composites cured with high-intensity halogen lights. , 2004, European journal of oral sciences.

[12]  F Rueggeberg,et al.  Contemporary issues in photocuring. , 1999, Compendium of continuing education in dentistry. (Jamesburg, N.J. : 1995). Supplement.

[13]  D. Charlton,et al.  Thermal emission and curing efficiency of LED and halogen curing lights. , 2005, Operative dentistry.

[14]  J. W. Curtis,et al.  Effect of light intensity and exposure duration on cure of resin composite. , 1994, Operative dentistry.

[15]  M. Okazaki,et al.  Thermal analysis of dental resins cured with blue light-emitting diodes (LEDs). , 2002, Journal of biomedical materials research.

[16]  R. Nomoto,et al.  Effect of light intensity on polymerization of light-cured composite resins. , 1994, Dental materials journal.

[17]  P. Andreou,et al.  Knoop hardness of ten resin composites irradiated with high-power LED and quartz-tungsten-halogen lights. , 2005, Biomaterials.

[18]  B. Hugo,et al.  Effect of high intensity vs. soft-start halogen irradiation on light-cured resin-based composites. Part II: Hardness and solubility. , 2004, American journal of dentistry.

[19]  A. Bush,et al.  A comparison of polymerization by light-emitting diode and halogen-based light-curing units. , 2002, Journal of the American Dental Association.

[20]  J. Ferracane,et al.  Wear and Marginal Breakdown of Composites with Various Degrees of Cure , 1997, Journal of dental research.

[21]  R. G. Craig,et al.  Correlation of Parameters used to Estimate Monomer Conversion in a Light-cured Composite , 1988, Journal of dental research.

[22]  H. Cardash,et al.  Post-irradiation polymerization of different anterior and posterior visible light-activated resin composites. , 1992, Dental materials : official publication of the Academy of Dental Materials.

[23]  K. Jandt,et al.  Depth of cure and compressive strength of dental composites cured with blue light emitting diodes (LEDs). , 2000, Dental materials : official publication of the Academy of Dental Materials.

[24]  F. Rueggeberg,et al.  Correlation of bottom-to-top surface microhardness and conversion ratios for a variety of resin composite compositions. , 2004, Operative dentistry.

[25]  V. Bagnato,et al.  Hardness evaluation of a dental composite polymerized with experimental LED-based devices. , 2001, Dental materials : official publication of the Academy of Dental Materials.

[26]  J. W. Curtis,et al.  Factors affecting cure at depths within light-activated resin composites. , 1993, American journal of dentistry.

[27]  K. Söderholm,et al.  How light irradiance and curing time affect monomer conversion in light-cured resin composites. , 2003, European journal of oral sciences.

[28]  J L Ferracane,et al.  Correlation between hardness and degree of conversion during the setting reaction of unfilled dental restorative resins. , 1985, Dental materials : official publication of the Academy of Dental Materials.

[29]  L. F. Schneider,et al.  Effect of the increase of energy density on Knoop hardness of dental composites light-cured by conventional QTH, LED and xenon plasma arc. , 2005, Brazilian dental journal.

[30]  A. Kakaboura,et al.  Acid-base reaction and fluoride release profiles in visible light-cured polyacid-modified composite restoratives (compomers). , 1998, Dental materials : official publication of the Academy of Dental Materials.

[31]  R. Loney,et al.  Effect of distance on the power density from two light guides. , 2000, Journal of esthetic dentistry.

[32]  Olaf Althoff,et al.  Curing performance of a new-generation light-emitting diode dental curing unit. , 2004, Journal of the American Dental Association.

[33]  D. Charlton,et al.  Polymerization efficiency of LED curing lights. , 2002, Journal of esthetic and restorative dentistry : official publication of the American Academy of Esthetic Dentistry ... [et al.].