Investigation of Closed-Loop Manufacturing with Acrylonitrile Butadiene Styrene over Multiple Generations Using Additive Manufacturing

This study examines the changes in physical and mechanical properties of acrylonitrile butadiene styrene (ABS) when manufactured using fused filament fabrication (FFF) 3D printing across multiple recycling phases. Tests were carried out initially using virgin ABS, which subsequently underwent two successive closed-loop filament extrusion and 3D printing phases. For each endpoint manufacturing phase, samples were examined to monitor the changes in thermal characteristics, mechanical properties, and polymer degradation. It was found that there was a series of physical changes of the polymer, which resulted in reduced melt flow, increased glass transition temperature, and the generation of carbonyl groups, which may be attributed to the thermal oxidative breakdown of both styrene acrylonitrile (SAN) and butadiene components of ABS. The recycled polymer also showed a reduction in both tensile and compressive strengths compared to the virgin material. However, compared to one-time recycled ABS, two-times recycled ABS showed increased strength, implying that increased recycle state of the polymer may be advantageous with respect to mechanical properties and potential manufacturing applications. This study ultimately demonstrates the potential to leverage additive manufacturing (AM) toward a closed-loop manufacturing paradigm by using waste ABS across several life cycles.

[1]  Chris E. Scott,et al.  Influence of initial sheet temperature on ABS thermoforming , 2001 .

[2]  Ian Gibson,et al.  A low carbon footprint approach to the reconstitution of plastics into 3D-printer filament for enhanced waste reduction , 2017 .

[3]  Sara V Orski,et al.  Validation of ATR FT-IR to identify polymers of plastic marine debris, including those ingested by marine organisms. , 2018, Marine pollution bulletin.

[4]  Robert A. Malloy,et al.  Plastic Part Design for Injection Molding: An Introduction , 1994 .

[5]  J. Jambeck,et al.  The Chinese import ban and its impact on global plastic waste trade , 2018, Science Advances.

[6]  Roberto Scaffaro,et al.  Physical properties of virgin-recycled ABS blends: Effect of post-consumer content and of reprocessing cycles , 2012 .

[7]  Liu Tengfei,et al.  Recycling and remanufacturing of 3D printed continuous carbon fiber reinforced PLA composites , 2017 .

[8]  Francesco Penta,et al.  A comparison between mechanical properties of specimens 3D printed with virgin and recycled PLA , 2019, Procedia CIRP.

[9]  Ian Gibson,et al.  Customised design of a patient specific 3D printed whole mandible implant , 2017 .

[10]  Ian Gibson,et al.  Design of Three-Dimensional, Triply Periodic Unit Cell Scaffold Structures for Additive Manufacturing , 2018 .

[11]  Keith Smith,et al.  Reprocessing Acrylonitrile-Butadiene-Styrene Plastics: Structure-Property Relationships , 2007 .

[12]  David A. Roberson,et al.  Failure Analysis and Anisotropy Evaluation of 3D-Printed Tensile Test Specimens of Different Geometries and Print Raster Patterns , 2016, Journal of Failure Analysis and Prevention.

[13]  Mohsen Esfahanian,et al.  Effect of reprocessing on shrinkage and mechanical properties of ABS and investigating the proper blend of virgin and recycled ABS in injection molding , 2014 .

[14]  Joshua M. Pearce,et al.  Fused Particle Fabrication 3-D Printing: Recycled Materials’ Optimization and Mechanical Properties , 2018, Materials.

[15]  AndersonIsabelle.  Mechanical Properties of Specimens 3D Printed with Virgin and Recycled Polylactic Acid , 2017 .

[16]  Joshua M. Pearce,et al.  Anisotropic mechanical property variance between ASTM D638-14 type i and type iv fused filament fabricated specimens , 2018, Polymer Testing.

[17]  Richard C. Thompson,et al.  Our plastic age , 2009, Philosophical Transactions of the Royal Society B: Biological Sciences.

[18]  Rosa Yeh,et al.  Detection of degradation of ABS materials via DSC , 2006 .

[19]  M. Mohammed,et al.  Fabrication of microfluidic devices: improvement of surface quality of CO2 laser machined poly(methylmethacrylate) polymer , 2016 .

[20]  Joshua M. Pearce,et al.  Tightening the loop on the circular economy: Coupled distributed recycling and manufacturing with recyclebot and RepRap 3-D printing , 2018 .

[21]  Joshua M. Pearce,et al.  Life Cycle Analysis of Distributed Recycling of Post-consumer High Density Polyethylene for 3-D Printing Filament , 2014 .

[23]  J. Silva,et al.  Calcium Phosphate Coatings by Sol-Gel on Acrylonitrile-butadiene-styrene Substrate , 2016 .

[24]  Bj Benny Luijsterburg,et al.  Assessment of plastic packaging waste : material origin, methods, properties , 2014 .

[25]  P. Wright,et al.  Anisotropic material properties of fused deposition modeling ABS , 2002 .

[26]  Joshua M. Pearce,et al.  RepRapable Recyclebot: Open source 3-D printable extruder for converting plastic to 3-D printing filament , 2018, HardwareX.

[27]  Joshua M. Pearce,et al.  Distributed recycling of waste polymer into RepRap feedstock , 2013 .

[28]  O. Traoré,et al.  Fabrication of Acrylonitrile-Butadiene-Styrene Nanostructures with Anodic Alumina Oxide Templates, Characterization and Biofilm Development Test for Staphylococcus epidermidis , 2015, PLoS ONE.

[29]  Jiajun Wang,et al.  Three-dimensional Printed Acrylonitrile Butadiene Styrene Framework Coated with Cu-BTC Metal-organic Frameworks for the Removal of Methylene Blue , 2014, Scientific Reports.

[30]  Anoop Kumar Sood,et al.  Experimental investigation and empirical modelling of FDM process for compressive strength improvement , 2012 .

[31]  Joshua M. Pearce,et al.  Environmental Life Cycle Analysis of Distributed Three-Dimensional Printing and Conventional Manufacturing of Polymer Products , 2013 .

[32]  Ian Gibson,et al.  Additive manufacturing technologies : 3D printing, rapid prototyping, and direct digital manufacturing , 2015 .

[33]  P. Tarantili,et al.  Stability of ABS Compounds Subjected to Repeated Cycles of Extrusion Processing , 2009 .

[34]  J. Baeyens,et al.  Recycling and recovery routes of plastic solid waste (PSW): a review. , 2009, Waste management.

[35]  Alberto Boschetto,et al.  Finishing of Fused Deposition Modeling parts by CNC machining , 2016 .