A novel five-axis rough machining method for efficient manufacturing of centrifugal impeller with free-form blades

This paper presents a novel methodology and algorithm for efficient manufacturing of the centrifugal impeller with free-form blades. Aim at the character of the centrifugal impeller blade surface, by the mathematical analysis and comparing method between the impellers with the free-form blade and ruled blade, the approximated blade with ruled surfaces is proposed as the simpler target for the rough machining of the impeller. For the slighter twist and efficient calculating, three machining areas are obtained by the two adjacent facing blades and the splitter, and four machining layers are obtained by intersections between the blades/splitters and hubs which have the same shapes but different locations along the direction from hub to shroud. The tool paths on each sun areas and layers are divided into two parts. Two computational methods of the tool axis and feed rate number are proposed to achieve the consummate equilibrium of the efficiency and the wanted profile for the following finish machining. The novel five-axis rough machining tool paths are calculated and a practical machining mold is presented.

[1]  Chih-Hsing Chu,et al.  Tool path planning for five-axis flank milling with developable surface approximation , 2006 .

[2]  H-Z Fan,et al.  Optimizing tool-path generation for three-axis machining of a sculptured impeller blade surface , 2012 .

[3]  Peiqing Ye,et al.  Local interference detection and avoidance in five-axis NC machining of sculptured surfaces , 2005 .

[4]  L.-C. Chuang,et al.  A five-axis rough machining approach for a centrifugal impeller , 2004 .

[5]  Yoram Koren,et al.  Efficient Tool-Path Planning for Machining Free-Form Surfaces , 1996 .

[6]  Aun Neow Poo,et al.  Adaptive iso-planar tool path generation for machining of free-form surfaces , 2003, Comput. Aided Des..

[7]  Bahattin Koc,et al.  Ellipse-offset approach and inclined zig-zag method for multi-axis roughing of ruled surface pockets , 1998, Comput. Aided Des..

[8]  F. Frank Chen,et al.  Efficient rough-cut plan for machining an impeller with a 5-axis NC machine , 2008, Int. J. Comput. Integr. Manuf..

[9]  Guang Xi,et al.  Efficient tool path planning for five-axis surface machining with a drum-taper cutter , 2003 .

[10]  Joost Duflou,et al.  A geometric modeling and five-axis machining algorithm for centrifugal impellers , 1997 .

[11]  L.-C. Chuang,et al.  An Integrated Machining Approach for a Centrifugal Impeller , 2003 .

[12]  Sanjay E. Sarma,et al.  Generating 5-axis NC roughing paths directly from a tessellated representation , 2000, Comput. Aided Des..

[13]  Johanna Senatore,et al.  Analysis of improved positioning in five-axis ruled surface milling using envelope surface , 2005, Comput. Aided Des..

[14]  Gérard Poulachon,et al.  Optimal strategy for finishing impeller blades using 5-axis machining , 2012 .

[15]  J. Paulo Davim,et al.  Machining of Complex Sculptured Surfaces , 2012 .

[16]  Pyo Lim,et al.  Optimization of the rough cutting factors of impeller with five-axis machine using response surface methodology , 2009 .

[17]  Hong-Tsu Young,et al.  Integrated rough machining methodology for centrifugal impeller manufacturing , 2007 .

[18]  Kuan-Hung Chen.  Investigation of tool orientation for milling blade of impeller in five-axis machining , 2011 .

[19]  Sanjeev Bedi,et al.  NURBS approximation to the flank-milled surface swept by a cylindrical NC tool , 2012 .

[20]  Yoshimi Takeuchi,et al.  5-axis control rough cutting of an impeller with efficiency and accuracy , 1997, Proceedings of International Conference on Robotics and Automation.

[21]  Krishnan Suresh,et al.  Constant Scallop-height Machining of Free-form Surfaces , 1994 .