Modelling and Optimization of a Small Diesel Burner for Mobile Applications

While extensive research has been done on improving diesel engines, much less has been done on auxiliary heaters, which have their own design challenges. The study analyzes how to optimize the combustion performance of an auxiliary heater, a 6 kW diesel burner, by investigating key parameters affecting diesel combustion and their properties. A model of a small diesel heater, including a simulation of fuel injection and combustion process, was developed step-wise and verified against experimental results that can be used for scaling up to 25 kW heaters. The model was successfully applied to the burner, predicting the burner performance in comparison with experimental results. Three main variables were identified as important for the design. First, it was concluded that the distance from the ring cone to the nozzle is essential for the fluid dynamics and flame location, and that the ring cone should be moved closer to the nozzle for optimal performance. Second, the design of the swirl co-flow is important, and the swirl number of the inlet air should be kept above 0.6 to stabilize the flame location for the present burner design. Finally, the importance of the nozzle diameter to avoid divergent particle vaporization was pointed out.

[1]  H. Holroyd.  On the atomization of liquid jets , 1933 .

[2]  S. I. Yang,et al.  Spray combustion characteristics of kerosene/bio-oil part I: Experimental study , 2017 .

[3]  John H. Seinfeld,et al.  Fundamentals of Air Pollution Engineering , 1988 .

[4]  F. C. Lockwood,et al.  Prediction of the near burner region and measurements of NOx and particulate emissions in heavy fuel oil spray flames , 1993 .

[5]  Jianmin Yang,et al.  Large-eddy simulation of the flow normal to a flat plate including corner effects at a high Reynolds number , 2014 .

[6]  Huei-Huang Chiu,et al.  Advances and challenges in droplet and spray combustion. I. Toward a unified theory of droplet aerothermochemistry , 2000 .

[7]  Li Du,et al.  Impacts and mitigation of excess diesel-related NOx emissions in 11 major vehicle markets , 2017, Nature.

[8]  Félix Barreras,et al.  Design modification of the air diffuser in the burners of a fuel oil power plant. Part II: Interaction with the liquid spray , 2014 .

[9]  P. Senecal,et al.  Modeling high-speed viscous liquid sheet atomization , 1999 .

[10]  M. Wannassi,et al.  Numerical simulation of the flow through the blades of a swirl generator , 2016 .

[11]  Petre P. Teodorescu,et al.  Errors in Numerical Analysis , 2013 .

[12]  A. Buekens,et al.  Combustion Fundamentals , 2018, The Slipcover for The John Zink Hamworthy Combustion Handbook.

[13]  A. García,et al.  The role of detailed chemical kinetics on CFD diesel spray ignition and combustion modelling , 2011, Math. Comput. Model..

[14]  Yuanjiang Pei,et al.  Transported probability density function modelling of the vapour phase of an n-heptane jet at diesel engine conditions , 2013 .

[15]  P. A. Lakshminarayanan,et al.  Estimation of Particulate Matter from Smoke, Oil Consumption and Fuel Sulphur , 2016 .

[16]  Morten Simonsen,et al.  Does driving behavior matter? An analysis of fuel consumption data from heavy-duty trucks , 2015 .

[17]  A. Gallegos-Muñoz,et al.  Liquid penetration length in direct diesel fuel injection , 2008 .

[18]  J. Jedelsky,et al.  Energy considerations in spraying process of a spill-return pressure-swirl atomizer , 2014 .

[19]  David G. Lilley,et al.  Modeling of combustor swirl flows , 1974 .

[20]  K. Raja Gopal,et al.  In-cylinder fluid flow, turbulence and spray models—A review , 2009 .

[21]  Vagesh D. Narasimhamurthy,et al.  Numerical simulation of the turbulent wake behind a normal flat plate , 2009 .

[22]  Ajay K. Agrawal,et al.  Combustion Performance of Biodiesel and Diesel-Vegetable Oil Blends in a Simulated Gas Turbine Burner , 2009 .

[23]  A. Abdel-azim.  Fundamentals of Heat and Mass Transfer , 2011 .

[24]  Shanshan Yao,et al.  Effect of viscosities on structure and instability of sprays from a swirl atomizer , 2012 .

[25]  Zhijun Wu,et al.  Simulation study on spray combustion mechanism of diesel–gasoline blend fuels , 2015 .

[26]  Yu Shi,et al.  Multi-dimensional Modelling of Diesel Combustion: Review , 2010 .

[27]  J. H. Whitelaw,et al.  Coaxial jets with and without swirl , 1980, Journal of Fluid Mechanics.

[28]  J. Rao.  Pressure—Velocity Coupling in Steady Flows , 2017 .

[29]  Kenneth O. Smith,et al.  A comparison of the flowfields and emissions of high-swirl injectors and low-swirl injectors for lean premixed gas turbines , 2005 .

[30]  Z. Ling,et al.  Establishing a low-NOx and high-burnout performance in a large-scale, deep-air-staging laboratory furnace fired by a heavy-oil swirl burner , 2015 .

[31]  H. Ismail,et al.  Evaluation of non-premixed combustion and fuel spray models for in-cylinder diesel engine simulation , 2012 .

[32]  N. Syred,et al.  Combustion in Swirling Flows: A Review , 2017 .

[33]  V. Arkhipov,et al.  Combustion of sprayed liquid fuel in a swirling flow , 2005 .

[34]  L Gilmer,et al.  Hazardous air pollutant emissions from gas-fired combustion sources: emissions and the effects of design and fuel type. , 2001, Chemosphere.

[35]  Darell B. Harmon,et al.  Drop sizes from low speed jets , 1955 .

[36]  James F. Driscoll,et al.  Effect of Heat Release and Swirl on the Recirculation within Swirl-Stabilized Flames , 1985 .

[37]  Wei Shyy,et al.  Computational Techniques for Complex Transport Phenomena , 1997 .

[38]  S. Hochgreb,et al.  Measurements of non-reacting and reacting flow fields of a liquid swirl flame burner , 2015 .

[39]  Michael F. Modest,et al.  The Method of Spherical Harmonics ( PN -Approximation) , 2013 .

[40]  Luc Vervisch,et al.  Using numerics to help the understanding of non-premixed turbulent flames , 2000 .

[41]  I. Glassman.  Environmental Combustion Considerations , 1996 .

[42]  Igor Bonefačić,et al.  Improvement of fuel oil spray combustion inside a 7 MW industrial furnace: A numerical study , 2017 .

[43]  Biagio Ciuffo,et al.  Fuel consumption and CO2 emissions from passenger cars in Europe Laboratory versus real-world emissions , 2017 .

[44]  Rolf D. Reitz,et al.  Pressure-Swirl Atomization in the Near Field , 1999 .

[45]  Y. Duan,et al.  Evaluation of unsteadiness in effervescent sprays by analysis of droplet arrival statistics – The influence of fluids properties and atomizer internal design , 2011 .

[46]  S. Twiss,et al.  Application of Infrared Spectroscopy to Exhaust Gas Analysis , 1955 .

[47]  Michael Duoba,et al.  Ambient Temperature (20°F, 72°F and 95°F) Impact on Fuel and Energy Consumption for Several Conventional Vehicles, Hybrid and Plug-In Hybrid Electric Vehicles and Battery Electric Vehicle , 2013 .

[48]  Patrick Jenny,et al.  Modeling of turbulent dilute spray combustion , 2012 .

[49]  S. Gu,et al.  Flameless combustion with liquid fuel: A review focusing on fundamentals and gas turbine application , 2017 .

[50]  P. Ekdunge,et al.  Diesel fuel reformer for automotive fuel cell applications , 2009 .

[51]  A. Kuchma,et al.  On the evolution of a multicomponent droplet during nonisothermal diffusion growth or evaporation , 2014, Colloid Journal.

[52]  William A. Sirignano,et al.  Advances in droplet array combustion theory and modeling , 2014 .