Assessment of high-heat-flux thermal management schemes

This paper explores the recent research developments in high-heat-flux thermal management. Cooling schemes such as pool boiling, detachable heat sinks, channel flow boiling, microchannel and mini-channel heat sinks, jet-impingement, and sprays, are discussed and compared relative to heat dissipation potential, reliability, and packaging concerns. It is demonstrated that, while different cooling options can be tailored to the specific needs of individual applications, system considerations always play a paramount role in determining the most suitable cooling scheme. It is also shown that extensive fundamental electronic cooling knowledge has been amassed over the past two decades. Yet there is now a growing need for hardware innovations rather than perturbations to those fundamental studies. An example of these innovations is the cooling of military avionics, where research findings from the electronic cooling literature have made possible the development of a new generation of cooling hardware which promise order of magnitude increases in heat dissipation compared to today's cutting edge avionics cooling schemes.

[1]  L. Chow,et al.  HIGH HEAT FLUX SPRAY COOLING , 1997 .

[2]  P. J. Marto,et al.  Pool Boiling Heat Transfer From Enhanced Surfaces to Dielectric Fluids , 1982 .

[3]  Terrence W. Simon,et al.  High-heat-flux forced convection boiling from small regions , 1989 .

[4]  I. Mudawar,et al.  Correlation of sauter mean diameter and critical heat flux for spray cooling of small surfaces , 1995 .

[5]  S. M. You,et al.  Heater Orientation Effects on Pool Boiling of Micro-Porous-Enhanced Surfaces in Saturated FC-72 , 1996 .

[6]  I. Mudawar,et al.  Orientation effects on pool boiling critical heat flux (CHF) and modeling of CHF for near-vertical surfaces , 1999 .

[7]  D. C. Wadsworth,et al.  Critical heat flux from a simulated chip to a confined rectangular impinging jet of dielectric liquid , 1991 .

[8]  M. Monde.  Critical heat flux in saturated forced convective boiling on a heated disk with an impinging jet , 1985 .

[9]  R. Webb.  The Evolution of Enhanced Surface Geometries for Nucleate Boiling , 1981 .

[10]  Issam Mudawar,et al.  Two-Phase Electronic Cooling Using Mini-Channel and Micro-Channel Heat Sinks: Part 1—Design Criteria and Heat Diffusion Constraints , 1994 .

[11]  R. Pease,et al.  High-performance heat sinking for VLSI , 1981, IEEE Electron Device Letters.

[12]  R. H. Sabersky,et al.  Some Effects of the Orientation of the Heating Surface in Nucleate Boiling , 1963 .

[13]  Issam Mudawar,et al.  Immersion-Cooled Standard Electronic Clamshell Module: A Building Block for Future High-Flux Avionic Systems , 1994 .

[14]  三朗 戸田.  ミスト・クーリングに関する研究 : 第1報,噴霧流中の流れに直角な高温小平板によるミスト・クーリング実験 , 1972 .

[15]  I. Mudawar,et al.  Ultra-high critical heat flux (CHF) for subcooled water flow boiling—II: high-CHF database and design equations , 1999 .

[16]  Issam Mudawar,et al.  Channel height effects on forced-convection boiling and critical heat flux from a linear array of discrete heat sources , 1992 .

[17]  Van P. Carey,et al.  Geometry Effects on Critical Heat Flux for Subcooled Convective Boiling From an Array of Heated Elements , 1991 .

[18]  Issam Mudawar,et al.  Critical heat flux in a long, curved channel subjected to concave heating , 1999 .

[19]  Ronald D. Boyd,et al.  Subcooled water flow boiling at 1. 66 MPa under uniform high heat flux conditions , 1989 .

[20]  Michael J. Mackowski.  Requirements for High Flux Cooling of Future Avionics Systems , 1991 .

[21]  Kazuo Araki,et al.  Local Heat-transfer Coefficient in Spray Cooling of Hot Surface , 1988 .

[22]  N. Zuber.  The Hydrodynamic Crisis in Pool Boiling of Saturated and Subcooled Liquids , 1963 .

[23]  Gary F. Goth,et al.  Dual-tapered-piston (DTP) module cooling for IBM Enterprise System/9000 systems , 1992, IBM J. Res. Dev..

[24]  I. Mudawar,et al.  Ultra-high critical heat flux (CHF) for subcooled water flow boiling—I: CHF data and parametric effects for small diameter tubes , 1999 .

[25]  W. R. Gambill.  BURNOUT IN BOILING HEAT TRANSFER. PART II. SUBCOOLED FORCED-CONVECTION SYSTEMS. , 1968 .

[26]  Y. Katto,et al.  Burnout in a high heat-flux boiling system with an impinging jet , 1978 .

[27]  M. Monde,et al.  Critical heat flux in saturated forced convective boiling on a heated disk with multiple impinging jets , 1987 .

[28]  Mohamed S. El-Genk,et al.  Transient boiling from inclined and downward-facing surfaces in a saturated pool , 1993 .

[29]  I. Mudawar,et al.  Single- and Two-Phase Convective Heat Transfer From Smooth and Enhanced Microelectronic Heat Sources in a Rectangular Channel , 1989 .

[30]  Arthur E. Bergles,et al.  Boiling Heat Transfer Characteristics of Simulated Microelectronic Chips with Detachable Heat Sinks , 1986 .

[31]  A. Howard,et al.  An analytical model for near-saturated pool boiling critical heat flux on vertical surfaces , 1997 .

[32]  D. Seals,et al.  Liquid flow-through cooling for avionics applications , 1991, Proceedings of the IEEE 1991 National Aerospace and Electronics Conference NAECON 1991.

[33]  Issam Mudawar,et al.  Orientation Effects on Critical Heat Flux From Discrete, In-Line Heat Sources in a Flow Channel , 1993 .

[34]  F. F. Simon,et al.  A visual study of velocity and buoyancy effects on boiling nitrogen , 1966 .

[35]  Ronald D. Boyd,et al.  Subcooled Flow Boiling Critical Heat Flux (CHF) and Its Application to Fusion Energy Components. Part I. A Review of Fundamentals of CHF and Related Data Base , 1985 .

[36]  Issam Mudawar,et al.  Critical heat flux in subcooled flow boiling of fluorocarbon liquid on a simulated electronic chip in a vertical rectangular channel , 1989 .

[37]  B. L. Bainbridge,et al.  Ex-vessel boiling experiments: laboratory- and reactor-scale testing of the flooded cavity concept for in-vessel core retention Part I: Observation of quenching of downward-facing surfaces , 1997 .

[38]  T. Hughes,et al.  Critical Heat Fluxes for Curved Surfaces during Subcooled Flow Boiling , 1975 .

[39]  Yoshiro Katto,et al.  Study of the Mechanism of Burn-Out in Boiling System of High Burn-Out Heat Flux , 1973 .

[40]  Issam Mudawar,et al.  Determination of the local quench curve for spray-cooled metallic surfaces , 1989 .

[41]  I. Mudawar,et al.  Parametric Investigation Into the Effects of Pressure, Subcooling, Surface Augmentation and Choice of Coolant on Pool Boiling in the Design of Cooling Systems for High-Power-Density Electronic Chips , 1990 .

[42]  Sushil H. Bhavnani,et al.  An Integral Heat Sink for Cooling Microelectronic Components , 1993 .

[43]  Ronald D. Boyd,et al.  Subcooled Water Flow Boiling Experiments Under Uniform High Heat Flux Conditions , 1988 .

[44]  Arthur E. Bergles,et al.  An experimental study of critical heat flux in very high heat flux subcooled boiling , 1994 .

[45]  I. Mudawar,et al.  Comparison of Two-Phase Electronic Cooling Using Free Jets and Sprays , 1995 .

[46]  I. Mudawar,et al.  Optimization of Enhanced Surfaces for High Flux Chip Cooling by Pool Boiling , 1993 .

[47]  Issam Mudawar,et al.  Effects of Orientation on Critical Heat Flux From Chip Arrays During Flow Boiling , 1992 .

[48]  I. Mudawar,et al.  Experimental and numerical study of quenching complex-shaped metallic alloys with multiple, overlapping sprays , 1995 .

[49]  Issam Mudawar,et al.  A Multi-Kilowatt Immersion-Cooled Standard Electronic Clamshell Module for Future Aircraft Avionics , 1994 .

[50]  Issam Mudawar,et al.  Assessment of CHF Enhancement Mechanisms in a Curved, Rectangular Channel Subjected to Concave Heating , 1999 .

[51]  Andreas K. Freund,et al.  Performance of a liquid‐nitrogen‐cooled, thin silicon crystal monochromator on a high‐power, focused wiggler synchrotron beam , 1995 .

[52]  W. Nakayama,et al.  Single chamber compact thermosyphons with micro-fabricated components , 2000, ITHERM 2000. The Seventh Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems (Cat. No.00CH37069).

[53]  A. D. Messina,et al.  Effects of precise arrays of pits on nucleate boiling , 1981 .

[54]  Issam Mudawar,et al.  A universal approach to predicting temperature response of metallic parts to spray quenching , 1994 .

[55]  I. Mudawar,et al.  Optimizing and Predicting CHF in Spray Cooling of a Square Surface , 1996 .

[56]  I. Mudawar,et al.  Microelectronic Cooling by Enhanced Pool Boiling of a Dielectric Fluorocarbon Liquid , 1989 .

[57]  Issam Mudawar,et al.  Design Parameters and Practical Considerations in the Two-Phase Forced-Convection Cooling of Multi-Chip Modules , 1992 .

[58]  A. Bergles,et al.  Characteristics of Nucleate Pool Boiling From Porous Metallic Coatings , 1982 .

[59]  I. P. Vishnev.  Effect of orienting the hot surface with respect to the gravitational field on the critical nucleate boiling of a liquid , 1973 .

[60]  Kaichiro Mishima,et al.  The effect of flow direction and magnitude on CHF for low pressure water in thin rectangular channels , 1985 .

[61]  Issam Mudawar,et al.  An Ultra-High Power Two-Phase Jet-Impingement Avionic Clamshell Module , 1996 .

[62]  Issam Mudawar,et al.  A theoretical model for flow boiling CHF from short concave heaters , 1995 .

[63]  I. Mudawar,et al.  Two-Phase Electronic Cooling Using Mini-Channel and Micro-Channel Heat Sinks: Part 2—Flow Rate and Pressure Drop Constraints , 1994 .

[64]  Issam Mudawar,et al.  High flux boiling in low flow rate, low pressure drop mini-channel and micro-channel heat sinks , 1994 .

[65]  Terrence W. Simon,et al.  Subcooled flow boiling over a thin, low-capacitance surface on a concave wall , 1995 .

[66]  R. Frieser,et al.  Heat Transfer of Modified Silicon Surfaces , 1980 .

[67]  Randolph J. Sheffield,et al.  High heat flux spray cooling , 1994 .

[68]  L. Wachters,et al.  The heat transfer from a hot wall to impinging water drops in the spheroidal state , 1966 .

[69]  Issam Mudawar,et al.  Nucleate Boiling and Critical Heat Flux From Protruded Chip Arrays During Flow Boiling , 1993 .

[70]  I. Mudawar,et al.  Enhancement of boiling heat transfer using highly wetting liquids with pressed-on fins at low contact forces , 1997 .

[71]  Issam Mudawar,et al.  Direct-immersion cooling for high power electronic chips , 1992, [1992 Proceedings] Intersociety Conference on Thermal Phenomena in Electronic Systems.

[72]  Gian Piero Celata,et al.  Burnout in highly subcooled water flow boiling in small diameter tubes , 1993 .

[73]  Terrence W. Simon,et al.  Heat Transfer From a Small Heated Region to R-113 and FC-72 , 1989 .

[74]  I. Mudawar,et al.  Forced-convection boiling and critical heat flux from a linear array of discrete heat sources , 1992 .