Multidisciplinary Design Optimization of Low-Airframe-Noise Transport Aircraft

The objective of this research is to examine how to design low-airframe-noise transport aircraft using Multidisciplinary Design Optimization (MDO). This involves optimizing aircraft to minimize maximum-take-off-weight, while constraining noise at the approach condition. A design methodology which incorporates noise as a design constraint into an MDO formulation is presented. An MDO framework was designed by integrating aircraft conceptual design tools previously developed at Virginia Tech with the Aircraft Noise Prediction Program (ANOPP). Design studies are presented for cantilever wing and Strut-Braced Wing (SBW) transport aircraft with 300 passengers and a 7,700 nm range. The results show that reducing airframe noise by reducing approach speed alone, will not provide significant noise reduction without a large performance and weight penalty. Therefore, more dramatic changes to the aircraft design are needed to achieve a significant airframe noise reduction. Another study showed that the trailing-edge (TE) flap can be eliminated, as well as all the noise associated with that device, without incurring a significant weight and performance penalty. If noise due to the leading-edge (LE) slats and landing gear are reduced, which is currently being pursued, the elimination of the flap will be very significant as the clean wing noise will be the next ‘noise barrier’. Lastly, an airframe noise analysis showed that a SBW aircraft, with short fuselage-mounted landing gear, could have a similar or potentially a lower airframe noise level than a cantilever wing aircraft.

[1]  Rakesh K. Kapania,et al.  Transport Weight Reduction through MDO: The Strut-Braced Wing Transonic Transport , 2005 .

[2]  E. Torenbeek,et al.  Synthesis of Subsonic Airplane Design , 1979 .

[3]  Erik D. Olson,et al.  Applications of Response Surface-Based Methods to Noise Analysis in the Conceptual Design of Revolutionary Aircraft , 2004 .

[4]  Raphael T. Haftka,et al.  Multidisciplinary design optimization of a transonic commercial transport with a strut-braced wing , 1999 .

[5]  Ricardo A. Burdisso,et al.  Wind Tunnel Aeroacoustic Measurements of a 26%-scale 777 Main Landing Gear , 2004 .

[6]  David P. Lockard,et al.  The Airframe Noise Reduction Challenge , 2004 .

[7]  Bernard Grossman,et al.  Multidisciplinary design optimization of a strut-braced wing transonic transport , 2000 .

[8]  Karl A. Geiselhart,et al.  Integration of Propulsion-Airframe-Aeroacoustic Technologies and Design Concepts for a Quiet Blended-Wing-Body Transport , 2004 .

[9]  G. M. Lilley,et al.  THE PREDICTION OF AIRFRAME NOISE AND COMPARISON WITH EXPERIMENT , 2001 .

[10]  R. H. Liebeck,et al.  Design of the Blended-Wing-Body subsonic transport , 2002 .

[11]  Bernard Grossman,et al.  Conceptual Design Studies of a Strut-Braced Wing Transonic Transport , 2000 .

[12]  Fei Li,et al.  High Resolution Calculation of a Simplified Landing Gear , 2004 .

[13]  Yueping Guo,et al.  An Empirical Model for Landing Gear Noise Prediction , 2004 .

[14]  Ilan Kroo,et al.  A Framework for Aircraft Conceptual Design and Environmental Performance Studies , 2004 .

[15]  Leifur Leifsson,et al.  Multidisciplinary Design Optimization of Low-Noise Transport Aircraft , 2005 .

[16]  Ilan Kroo,et al.  Aircraft optimization for minimal environmental impact , 2002 .

[17]  Peter K. C. Rudolph,et al.  High-Lift Systems on Commercial Subsonic Airliners , 1996 .

[18]  Amir H. Naghshineh-Pour,et al.  Structural Optimization and Design of a Strut-Braced Wing Aircraft , 1998 .

[19]  Zoltán S. Spakovszky,et al.  NOISE REDUCTION ASSESSMENTS AND PRELIMINARY DESIGN IMPLICATIONS FOR A FUNCTIONALLY-SILENT AIRCRAFT , 2004 .

[20]  Renaud Davy,et al.  Flight Test Investigation of Add-On Treatments to Reduce Aircraft Airframe Noise , 2005 .

[21]  Sherilyn A. Brown,et al.  Propulsion Airframe Aeroacoustics Technology Evaluation and Selection Using a Multi-Attribute Decision Making Process and Non-Deterministic Design , 2004 .

[22]  C. P. van Dam,et al.  The aerodynamic design of multi-element high-lift systems for transport airplanes , 2002 .

[23]  Joel M. Grasmeyer,et al.  Multidisciplinary Design Optimization of a Strut-Braced Wing Aircraft , 1998 .

[24]  Ilan Kroo,et al.  OPTIMIZING AIRCRAFT AND OPERATIONS FOR MINIMUM NOISE , 2002 .

[25]  W. E. Zorumski.  Aircraft noise prediction program theoretical manual, part 1 , 1982 .

[26]  Lloyd R. Jenkinson,et al.  Adapting Civil Aircraft Conceptual Design Methods to Account for Broader Based Constraints , 1997 .

[27]  Werner Dobrzynski,et al.  Design and Testing of Low Noise Landing Gears , 2005 .

[28]  Philippe-Andre Tetrault,et al.  Numerical Prediction of the Interference Drag of a Streamlined Strut Intersecting a Surface in Transonic Flow , 2000 .

[29]  Roy T. Schemensky,et al.  Development of an Empirically Based Computer Program to Predict the Aerodynamic Characteristics of Aircraft. Volume I. Empirical Methods , 1973 .