Evaluation of a novel mobile device app for value-maximized bucking by chainsaw

ABSTRACT Cross-cutting of felled trees into logs (“bucking”) is a critical step in converting standing timber into end products, as it predetermines and limits number, type and value of products that can be produced from the logs. Bucking by chainsaw is currently not aided by information technology and volume and value recovery depend on the chainsaw operator’s proficiency. A recently presented novel mobile device-based application (“T4E Bucking App”) for assisting value-maximized bucking by chainsaw was evaluated during harvesting in a mature beech stand regarding taper curve estimation accuracy. Further, its bucking patterns were benchmarked against an experienced chainsaw operator’s choice and time consumption for app operation was determined. Taper curves were inadequately approximated and log mid diameters (1.0 cm, SD=2.4) and log volume (0.02 m3 under bark [UB] m3, SD=0.04) were significantly overestimated. Consequently, total observed volume (–8.7%) and value (–8.1%) were smaller than estimated. Inappropriate pricing and insufficient top diameters caused further reductions. Thus, total recovered volume (59.61 m3 UB; –8.8%) and value (€2,099.66; –8.6%) were smaller than estimated. Chainsaw operator’s totals differed marginally (58.59 m3 UB; €2,117.99). About 85% of the variation of time consumption for working with the app was explained by tree volume and number of grade sections. After accounting for time consumption, net value recovery was 5.1% lower than in the chainsaw operator’s case. The T4E Bucking App nevertheless represents a first step towards digitalization of motor-manual bucking and may soon be enhanced by more accurate taper curves derived from terrestrial laser scanning data.

[1]  Christoph Gollob,et al.  Forest Inventory with Long Range and High-Speed Personal Laser Scanning (PLS) and Simultaneous Localization and Mapping (SLAM) Technology , 2020, Remote. Sens..

[2]  Juha Hyyppä,et al.  Accurate derivation of stem curve and volume using backpack mobile laser scanning , 2020, ISPRS Journal of Photogrammetry and Remote Sensing.

[3]  M. Vastaranta,et al.  Assessing log geometry and wood quality in standing timber using terrestrial laser-scanning point clouds , 2018, Forestry: An International Journal of Forest Research.

[4]  D. Jaeger,et al.  How Climate Change Will Affect Forest Composition and Forest Operations in Baden-Württemberg—A GIS-Based Case Study Approach , 2017 .

[5]  Eric R. Labelle,et al.  The effect of quality bucking and automatic bucking on harvesting productivity and product recovery in a pine-dominated stand , 2017, European Journal of Forest Research.

[6]  Michael Halpin,et al.  Policy Brief , 2016, Journal of health and social behavior.

[7]  Juha Hyyppä,et al.  Automated Stem Curve Measurement Using Terrestrial Laser Scanning , 2014, IEEE Transactions on Geoscience and Remote Sensing.

[8]  Natascia Magagnotti,et al.  A new guide for work studies in forestry , 2013 .

[9]  Jingxin Wang,et al.  A Three-Dimensional Bucking System for Optimal Bucking of Central Appalachian Hardwoods , 2009 .

[10]  Glen Murphy,et al.  Determining Stand Value and Log Product Yields Using Terrestrial Lidar and Optimal Bucking: A Case Study , 2008 .

[11]  François Grondin,et al.  Improvements of the Dynamic Programming Algorithm for tree Bucking , 2007 .

[12]  Veli-Pekka Kivinen,et al.  Design and testing of stand-specific bucking instructions for use on modern cut-to-length harvesters , 2007 .

[13]  Andre Laroze,et al.  A Linear Programming, Tabu Search Method for Solving Forest-Level Bucking Optimization Problems , 1999 .

[14]  S. Bowers.  Increased Value through Optimal Bucking , 1998 .

[15]  J. B. Pickens,et al.  Choosing Prices to Optimally Buck Hardwood Logs with Multiple Log-Length Demand Restrictions , 1997, Forestry sciences.

[16]  Brian J. Greber,et al.  Using Tabu Search To Generate Stand-Level, Rule-Based Bucking Patterns , 1997 .

[17]  Eldon D. Olsen,et al.  Questions about optimal bucking , 1991 .

[18]  G. Murphy.  An economic analysis of final log manufacturing locations in the steep terrain radiata pine plantations of New Zealand , 1987 .

[19]  H. G. Daellenbach,et al.  Technical Note - Forest Outturn Optimization by Dantzig-Wolfe Decomposition and Dynamic Programming Column Generation , 1985, Oper. Res..

[20]  B. Faaland,et al.  Log Bucking and Lumber Manufacturing Using Dynamic Programming , 1984 .

[21]  R Core Team,et al.  R: A language and environment for statistical computing. , 2014 .

[22]  A. Akay,et al.  Applying optimum bucking method in producing Taurus Fir (Abies cilicica) logs in Mediterranean Region of Turkey. , 2010 .

[23]  Jürgen Roßmann,et al.  The virtual forest: Robotics and simulation technology as the basis for new approaches to the biological and the technical production in the forest , 2009 .

[24]  M.,et al.  A METHOD TO ASSESS LOG VALUE LOSS CAUSED BY CROSS-CUTTING PRACTICE ON THE SKIDSITE , 2006 .

[25]  G. Murphy,et al.  Optimal bucking of Douglas fir taking into consideration external properties and wood density , 2005 .

[26]  Jingxin Wang,et al.  Optimal tree-stem bucking of northeastern species of China , 2004 .

[27]  J. Puumalainen,et al.  Optimal cross‐cutting and sensitivity analysis for various log dimension constraints by using dynamic programming approach , 1998 .

[28]  Stephen J. Pilkerton,et al.  OPTIMAL BUCKING: TWO TRIALS WITH COMMERCIAL OSU BUCK SOFTWARE , 1997 .

[29]  John Sessions,et al.  Manufacturing logs with computer-aided bucking at the stump , 1989 .

[30]  D. G. Briggs,et al.  Tree value system: description and assumptions. , 1989 .

[31]  David Andrew Waddell,et al.  A practical system for determining optimal tree bucking at the stump , 1988 .

[32]  G. A. Mendoza,et al.  A two-stage decision model for log bucking and allocation , 1986 .

[33]  M. Naesberg,et al.  Mathematical programming models for optimal log bucking , 1985 .